參數資料
型號： ST72331
廠商： 意法半導體
英文描述： 8-Bit MCU with 8 to 16K ROM/OTP/EPROM, 256 EEPROM, 384 to 512 Bytes RAM, ADC, WDG, SCI, SPI and 2 Timers(8位微控制器(8M))
中文描述： 8位微控制器與8至16K的光碟/雙層/存儲器，256的EEPROM，384字節RAM為512，藝發局，水分散粒劑，脊髓損傷，SPI和2計時器（8位微控制器（8米））
文件頁數： 72/98頁
文件大小： 1123K
代理商： ST72331
72/98
ST72331
SERIAL PERIPHERAL INTERFACE
(Cont’d)
4.6.5 Register Description
Control Register (CR)
Read/Write
Reset Value: 0000xxxx (0xh)
Bit 7 =
SPIE
Serial peripheral interrupt enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SPI interrupt is generated whenever SPIF=1
or MODF=1 in the SR register
Bit 6 =
SPE
Serial peripheral output enable.
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode, SS=0
(see
Section 4.6.4.5 Master Mode Fault
).
0: I/O port connected to pins
1: SPI alternate functions connected to pins
The SPE bit is cleared by reset, so the SPI periph-
eral is not initially connected to the external pins.
Bit 5 =
SPR2
Divider Enable.
This bit is set and cleared by software and it is
cleared by reset. It is used with the SPR[1:0] bits to
set the baud rate. Refer to
Table 18
.
0: Divider by 2 enabled
1: Divider by 2 disabled
Bit 4 =
MSTR
Master.
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode, SS=0
(see
Section 4.6.4.5 Master Mode Fault
).
0: Slave mode is selected
1: Master mode is selected, the function of the
SCK pin changes from an input to an output and
the functions of the MISO and MOSI pins are re-
versed.
Bit 3 =
CPOL
Clock polarity.
This bit is set and cleared by software. This bit de-
termines the steady state of the serial Clock. The
CPOL bit affects both the master and slave
modes.
0: The steady state is a low value at the SCK pin.
1: The steady state is a high value at the SCK pin.
Bit 2 =
CPHA
Clock phase.
This bit is set and cleared by software.
0: The first clock transition is the first data capture
edge.
1: The second clock transition is the first capture
edge.
Bit 1,0 =
SPR1
-
SPR0
Serial peripheral rate.
These bits are set and cleared by software. Used
with the SPR2 bit, they select one of six baud rates
to be used as the serial clock when the device is a
master.
These 2 bits have no effect in slave mode.
Table 18. Serial Peripheral Baud Rate
7
0
SPIE
SPE
SPR2
MSTR
CPOL
CPHA
SPR1
SPR0
Serial Clock
f
CPU
/4
f
CPU
/8
f
CPU
/16
f
CPU
/32
f
CPU
/64
f
CPU
/128
SPR2
1
0
0
1
0
0
SPR1
0
0
0
1
1
1
SPR0
0
0
1
0
0
1
134
相關PDF資料
PDF描述
ST72371 8-Bit MCUs with 16K ROM/OTP/EPROM, 512 Bytes RAM, ADC, DAC (PWM), Timer, IIC and SCI(8位微控制器(8M))
ST72372 8-Bit MCUs with 16K ROM/OTP/EPROM, 512 Bytes RAM, ADC, DAC (PWM), Timer, IIC and SCI(8位微控制器(8M))
ST72681 USB 2.0 HIGH-SPEED 8-BIT MCU FLASH DRIVE CONTROLLER
ST72753L4 8-BIT MCU FOR MONITORS WITH UP TO 32K ROM, 1K RAM, ADC, TIMER, SYNC, PWM/BRM, DDC/DMA & I2C
ST72753L5 8-BIT MCU FOR MONITORS WITH UP TO 32K ROM, 1K RAM, ADC, TIMER, SYNC, PWM/BRM, DDC/DMA & I2C
相關代理商/技術參數
參數描述
ST72331J2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER (MCU) WITH 8/16K ROM/OTP/EPROM.256 EEPROM.384/512 BYTES RAM.ADC.WDG.SCI.SPI & 2 TIMERS - SDIP42/56. QFP44/64
ST72331J2B1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST72331J2B6/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST72331J2T1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST72331J2T6/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*