參數資料
型號： ST72331
廠商： 意法半導體
英文描述： 8-Bit MCU with 8 to 16K ROM/OTP/EPROM, 256 EEPROM, 384 to 512 Bytes RAM, ADC, WDG, SCI, SPI and 2 Timers(8位微控制器(8M))
中文描述： 8位微控制器與8至16K的光碟/雙層/存儲器，256的EEPROM，384字節RAM為512，藝發局，水分散粒劑，脊髓損傷，SPI和2計時器（8位微控制器（8米））
文件頁數： 25/98頁
文件大?。?/td> 1123K
代理商： ST72331
25/98
ST72331
4 ON-CHIP PERIPHERALS
4.1 I/O PORTS
4.1.1 Introduction
The I/O ports offer different functional modes:
– transfer of data through digital inputs and outputs
and for specific pins:
– analog signal input (ADC)
– alternate signal input/output for the on-chip pe-
ripherals.
– external interrupt generation
An I/O port is composed of up to 8 pins. Each pin
can be programmed independently as digital input
(with or without interrupt generation) or digital out-
put.
4.1.2 Functional Description
Each port is associated to 2 main registers:
– Data Register (DR)
– Data Direction Register (DDR)
and some of them to an optional register:
– Option Register (OR)
Each I/O pin may be programmed using the corre-
sponding register bits in DDR and OR registers: bit
X corresponding to pin X of the port. The same cor-
respondence is used for the DR register.
The following description takes into account the
OR register, for specific ports which do not provide
this register refer to the I/O Port Implementation
Section 4.1.2.5
. The generic I/O block diagram is
shown on
Figure 20
.
4.1.2.1 Input Modes
The input configuration is selected by clearing the
corresponding DDR register bit.
In this case, reading the DR register returns the
digital value applied to the external I/O pin.
Different input modes can be selected by software
through the OR register.
Notes
:
1. All the inputs are triggered by a Schmitt trigger.
2. When switching from input mode to output
mode, the DR register should be written first to
output the correct value as soon as the port is con-
figured as an output.
Interrupt function
When an I/O is configured in Input with Interrupt,
an event on this I/O can generate an external In-
terrupt request to the CPU. The interrupt polarity is
given independently according to the description
mentioned in the Miscellaneous register or in the
interrupt register (where available).
Each pin can independently generate an Interrupt
request.
Each external interrupt vector is linked to a dedi-
cated group of I/O port pins (see Interrupts sec-
tion). If more than one input pin is selected simul-
taneously as interrupt source, this is logically
ORed. For this reason if one of the interrupt pins is
tied low, it masks the other ones.
4.1.2.2 Output Mode
The pin is configured in output mode by setting the
corresponding DDR register bit.
In this mode, writing “0” or “1” to the DR register
applies this digital value to the I/O pin through the
latch. Then reading the DR register returns the
previously stored value.
Note
: In this mode, the interrupt function is disa-
bled.
4.1.2.3 Digital Alternate Function
When an on-chip peripheral is configured to use a
pin, the alternate function is automatically select-
ed. This alternate function takes priority over
standard I/O programming. When the signal is
coming from an on-chip peripheral, the I/O pin is
automatically configured in output mode (push-pull
or open drain according to the peripheral).
When the signal is going to an on-chip peripheral,
the I/O pin has to be configured in input mode. In
this case, the pin’s state is also digitally readable
by addressing the DR register.
Notes:
1. Input pull-up configuration can cause an unex-
pected value at the input of the alternate peripher-
al input.
2. When the on-chip peripheral uses a pin as input
and output, this pin must be configured as an input
(DDR = 0).
Warning:
The alternate function must not be acti-
vated as long as the pin is configured as input with
interrupt, in order to avoid generating spurious in-
terrupts.
87
相關PDF資料
PDF描述
ST72371 8-Bit MCUs with 16K ROM/OTP/EPROM, 512 Bytes RAM, ADC, DAC (PWM), Timer, IIC and SCI(8位微控制器(8M))
ST72372 8-Bit MCUs with 16K ROM/OTP/EPROM, 512 Bytes RAM, ADC, DAC (PWM), Timer, IIC and SCI(8位微控制器(8M))
ST72681 USB 2.0 HIGH-SPEED 8-BIT MCU FLASH DRIVE CONTROLLER
ST72753L4 8-BIT MCU FOR MONITORS WITH UP TO 32K ROM, 1K RAM, ADC, TIMER, SYNC, PWM/BRM, DDC/DMA & I2C
ST72753L5 8-BIT MCU FOR MONITORS WITH UP TO 32K ROM, 1K RAM, ADC, TIMER, SYNC, PWM/BRM, DDC/DMA & I2C
相關代理商/技術參數
參數描述
ST72331J2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER (MCU) WITH 8/16K ROM/OTP/EPROM.256 EEPROM.384/512 BYTES RAM.ADC.WDG.SCI.SPI & 2 TIMERS - SDIP42/56. QFP44/64
ST72331J2B1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST72331J2B6/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST72331J2T1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST72331J2T6/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*