參數資料
型號: M66596FP
元件分類: 總線控制器
英文描述: UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封裝: 0.50 MM PITCH, LQFP-64
文件頁數: 91/133頁
文件大小: 1611K
代理商: M66596FP
M66596FP/WG
rev .1.00
2006.3.14
page 58 of 127
3.1.8.4 Stopping the internal clock supply (From a normal operating state to clock stop state)
The timing diagram of the transition from the normal operation state to the clock stop state of the controller is
shown in Figure 3.8. The transitions should be operated according to the following sequence.
(1) Software disables the internal clock suppliance.
"SCKE=0"
(2) Software waits until an internal clock stops.
(A waiting time of at least 300 ns is necessary.)
(3) Software disables the PLL.
"PLLC=0"
(4) Software waits for the PLL to stop.
(A waiting time of at least 300 ns is necessary.)
(5) Software disables reference clock suppliance.
"RCKE=0"
(6) Software waits until the reference clock stops.
(A waiting time of at least 300 ns is necessary.)
(7) Software disables the oscillation buffer.
"XCKE=0"
XCKE
RCKE
PLLC
SCKE
(2) min 300ns
(1)
Start of transit to
the clock stop
(3)
(5)
(4) min 300ns
(6) min 300ns
(7)
Figure 3.8 Transition control timing to the clock stop state
3.1.8.5 Starting the internal clock supply (From the clock stop state to the normal operating state: with
"ATCKM=1")
The timing diagram from the clock stop state to the normal operation state is shown in Figure 3.9. The timing
diagram is in the case of the auto clock supply function is enabled ("ATCKM=1"; recommended setting).
In this case, the controller operates registers when resume signal is detected. The controller changes to the normal
operation state by waiting for access prohibition time after resume interruption is generated. The register operation
by software is not required. If VBUS interrupt is occurs, the softwear need to enable the oscillation buffer
(1) The controller detects the resume signal or VBUS changes on a USB bus, and the INT_N pin is asserted.
(2) When resume signal is received, the controller automatically enables the oscillation buffer. "XCKE=1(H/W)"
When VBUS change occurs, the softwear needs to enable the oscillation buffer. "XCKE=1.
(3) The softwear waits until access is enabled. (A waiting time of at least 2.5 ms is necessary.)
(4) The controller automatically enables RCKE, PLLC, and SCKE during (3).
(5) Software performs resume processing depending on the interrupt factor, resume or attachment.
XCKE
Resume :H/W
VBUS chage :S/W
RCKE(H/W)
PLLC(H/W)
SCKE(H/W)
(3) 2.5ms (access disabled)
Clock stop
recovery
INT_N
Event
CS_N
(1),(2)
(4)
(5)
Figure 3.9 Recovery control timing from the clock stop state with “ATCKM=1”
相關PDF資料
PDF描述
M66596WG UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
M6XXLFXI OTHER CLOCK GENERATOR, QCC16
M300LFXIT 50 MHz, OTHER CLOCK GENERATOR, QCC16
M74HC00C1R HC/UH SERIES, QUAD 2-INPUT NAND GATE, PQCC20
M74HC157B1N HC/UH SERIES, QUAD 2 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDIP16
相關代理商/技術參數
參數描述
M66596FP#RB0Z 制造商:Renesas Electronics Corporation 功能描述:MCU - Trays 制造商:Renesas Electronics 功能描述:USB Device Controller 64-Pin LQFP Cut Tape 制造商:Renesas Electronics 功能描述:USB Device Controller 64-Pin LQFP Tray 制造商:Renesas 功能描述:USB Device Controller 64-Pin LQFP
M66596FPRB0Z 制造商:Renesas Electronics Corporation 功能描述:USB2.0 Dual Function Controller,LQFP64
M66596WG 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:ASSP (USB2.0 Dual Function Controller)
M66596WG#RB0Z 制造商:Renesas Electronics 功能描述:Tray 制造商:Renesas 功能描述:0
M6668 制造商:Tamura Corporation of America 功能描述: