參數資料
型號: TMP20F2810PBKAEP
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: Digital Signal Processors
中文描述: 數字信號處理器
文件頁數: 37/159頁
文件大?。?/td> 2084K
代理商: TMP20F2810PBKAEP
Functional Overview
37
March 2004 Revised October 2004
SGUS051A
PF2:
SYS:
GPIO:
EV:
McBSP:
SCI:
SPI:
ADC:
System Control Registers
GPIO Mux Configuration and Control Registers
Event Manager (EVA/EVB) Control Registers
McBSP Control and TX/RX Registers
Serial Communications Interface (SCI) Control and RX/TX Registers
Serial Peripheral Interface (SPI) Control and RX/TX Registers
12-Bit ADC Registers
3.2.19
General-Purpose Input/Output (GPIO) Multiplexer
Most of the peripheral signals are multiplexed with general-purpose I/O (GPIO) signals. This enables the user
to use a pin as GPIO if the peripheral signal or function is not used. On reset, all GPIO pins are configured
as inputs. The user can then individually program each pin for GPIO mode or Peripheral Signal mode. For
specific inputs, the user can also select the number of input qualification cycles. This is to filter unwanted noise
glitches.
3.2.20
32-Bit CPU-Timers (0, 1, 2)
CPU-Timers 0, 1, and 2 are identical 32-bit timers with presettable periods and with 16-bit clock prescaling.
The timers have a 32-bit count down register, which generates an interrupt when the counter reaches zero.
The counter is decremented at the CPU clock speed divided by the prescale value setting. When the counter
reaches zero, it is automatically reloaded with a 32-bit period value. CPU-Timer 2 is reserved for Real-Time
OS (RTOS)/BIOS applications. CPU-Timer 1 is also reserved for TI system functions. CPU-Timer 2 is
connected to INT14 of the CPU. CPU-Timer 1 can be connected to INT13 of the CPU. CPU-Timer 0 is for
general use and is connected to the PIE block.
3.2.21
Control Peripherals
The F281x and C281x support the following peripherals which are used for embedded control and
communication:
EV:
The event manager module includes general-purpose timers, full-compare/PWM units,
capture inputs (CAP) and quadrature-encoder pulse (QEP) circuits. Two such event
managers are provided which enable two three-phase motors to be driven or four
two-phase motors. The event managers on the F281x and C281x are compatible to the
event managers on the 240x devices (with some minor enhancements).
The ADC block is a 12-bit converter, single ended, 16-channels. It contains two
sample-and-hold units for simultaneous sampling.
ADC:
3.2.22
Serial Port Peripherals
The F281x and C281x support the following serial communication peripherals:
eCAN:
This is the enhanced version of the CAN peripheral. It supports 32 mailboxes, time stamping
of messages, and is CAN 2.0B-compliant.
This is the multichannel buffered serial port that is used to connect to E1/T1 lines,
phone-quality codecs for modem applications or high-quality stereo-quality Audio DAC
devices. The McBSP receive and transmit registers are supported by a 16-level FIFO. This
significantly reduces the overhead for servicing this peripheral.
McBSP:
相關PDF資料
PDF描述
TMS320F2812PGFMEP Digital Signal Processors
TMS320F2810PGFAEP Digital Signal Processors
TMX20F2810PBKAEP Digital Signal Processors
TMS320LC2404APGA DSP CONTROLLERS
TMP320LC2401APAGA DSP CONTROLLERS
相關代理商/技術參數
參數描述
TMP2681P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
TMP275 制造商:BB 制造商全稱:BB 功能描述:0.5∑C Digital Out Temperature Sensor
TMP275AID 功能描述:板上安裝溫度傳感器 0.5C Dig Out Temp Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP275AID 制造商:Texas Instruments 功能描述:IC TEMP SENSOR 12BIT
TMP275AID 制造商:Texas Instruments 功能描述:IC DIGITAL TEMP SENSOR