參數資料
型號： TMP20F2810PBKAEP
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： Digital Signal Processors
中文描述： 數字信號處理器
文件頁數： 18/159頁
文件大?。?/td> 2084K
代理商： TMP20F2810PBKAEP
Introduction
18
March 2004 Revised October 2004
SGUS051A
Table 22. Signal Descriptions
(Continued)
NAME
DESCRIPTION
PU/PD§
I/O/Z
PIN NO.
176-PIN
PGF
128-PIN
PBK
179-PIN
GHH
XINTF SIGNALS (2812 ONLY) (CONTINUED)
XMP/MC
F1
17
I
PD
Microprocessor/Microcomputer Mode Select. Switches
between microprocessor and microcomputer mode. When
high, Zone 7 is enabled on the external interface. When low,
Zone 7 is disabled from the external interface, and on-chip
boot ROM may be accessed instead. This signal is latched
into the XINTCNF2 register on a reset and the user can modify
this bit in software. The state of the XMP/MC pin is ignored
after reset.
XHOLD
E7
159
I
PU
External Hold Request. XHOLD, when active (low), requests
the XINTF to release the external bus and place all buses and
strobes into a high-impedance state. The XINTF will release
the bus when any current access is complete and there are no
pending accesses on the XINTF.
XHOLDA
K10
82
O/Z
External Hold Acknowledge. XHOLDA is driven active (low)
when the XINTF has granted a XHOLD request. All XINTF
buses and strobe signals will be in a high-impedance state.
XHOLDA is released when the XHOLD signal is released.
External devices should only drive the external bus when
XHOLDA is active (low).
XZCS0AND1
P1
44
O/Z
XINTF Zone 0 and Zone 1 Chip Select. XZCS0AND1 is active
(low) when an access to the XINTF Zone 0 or Zone 1 is
performed.
XZCS2
P13
88
O/Z
XINTF Zone 2 Chip Select. XZCS2 is active (low) when an
access to the XINTF Zone 2 is performed.
XZCS6AND7
B13
133
O/Z
XINTF Zone 6 and Zone 7 Chip Select. XZCS6AND7 is active
(low) when an access to the XINTF Zone 6 or Zone 7 is
performed.
XWE
N11
84
O/Z
Write Enable. Active-low write strobe. The write strobe
waveform is specified, per zone basis, by the Lead, Active,
and Trail periods in the XTIMINGx registers.
XRD
M3
42
O/Z
Read Enable. Active-low read strobe. The read strobe
waveform is specified, per zone basis, by the Lead, Active,
and Trail periods in the XTIMINGx registers. NOTE: The XRD
and XWE signals are mutually exclusive.
XR/W
N4
51
O/Z
Read Not Write Strobe. Normally held high. When low, XR/W
indicates write cycle is active; when high, XR/W indicates read
cycle is active.
Typical drive strength of the output buffer for all pins is 4 mA except for TDO, XCLKOUT, XF, XINTF, EMU0, and EMU1 pins, which are 8 mA.
I = Input, O = Output, Z = High impedance
§PU = pin has internal pullup; PD = pin has internal pulldown
相關PDF資料
PDF描述
TMS320F2812PGFMEP Digital Signal Processors
TMS320F2810PGFAEP Digital Signal Processors
TMX20F2810PBKAEP Digital Signal Processors
TMS320LC2404APGA DSP CONTROLLERS
TMP320LC2401APAGA DSP CONTROLLERS
相關代理商/技術參數
參數描述
TMP2681P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
TMP275 制造商:BB 制造商全稱:BB 功能描述:0.5∑C Digital Out Temperature Sensor
TMP275AID 功能描述:板上安裝溫度傳感器 0.5C Dig Out Temp Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP275AID 制造商:Texas Instruments 功能描述:IC TEMP SENSOR 12BIT
TMP275AID 制造商:Texas Instruments 功能描述:IC DIGITAL TEMP SENSOR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*