- 您現在的位置：買賣IC網 > PDF目錄383876 > T7234A Compliance with the New ETSI PSD Requirement PDF資料下載
參數資料
| 型號： | T7234A |
| 英文描述： | Compliance with the New ETSI PSD Requirement |
| 中文描述： | 符合新的ETSI PSD的要求 |
| 文件頁數： | 85/116頁 |
| 文件大?。?/td> | 1056K |
| 代理商： | T7234A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
January 1998
T7256 Single-Chip NT1 (SCNT1) Transceiver
Lucent Technologies Inc.
81
Questions and Answers
(continued)
U-Interface
(continued)
A9:
(continued)
This statement could be interpreted to mean that
a protector such as VR2 in Figure 20 should not
trip if subjected to a voltage of that amplitude.
This interpretation sets a lower limit on VR2’s
breakover rating. Since capacitor C16 will be
exposed to the same voltage as VR2, its voltage
rating must be greater than the maximum break-
over rating of VR2. This sets an upper limit on the
protector breakover voltage. The result is a need
for a capacitor typically rated at about 250 V.
However, an argument can be made that it
doesn’t matter whether VR2 trips under this con-
dition, since it is a fault condition anyway, and a
tripped protector won’t do any damage to a cen-
tral office ringer.
The only other similar requirement, then, is found
in Footnote 8, referenced in Section 7.5.3 of ANSI
T1.601. The footnote implies that the maximum
voltage that an NT will see during metallic testing
is 90 V. The breakover voltage VR2 must be large
enough not to trip during the application of the
test voltage mentioned in the footnote. This
means that a protector with a minimum breakover
voltage of
≥
90 V can be used that would permit a
capacitor of lower voltage rating (e.g., 150 V) to
be used. This is the approach we currently favor,
although Figure 20 illustrates the more conserva-
tive approach.
Q10:
What is the purpose of the 3300 pF capacitors
(C13 and C14) in Figure 20 in the data sheet
A10:
The capacitors are for common-mode noise
rejection. The ANSI T1.601 specification contains
no requirements on longitudinal noise immunity.
Therefore, these capacitors are not required in
order to meet the specification. However, there
are guidelines in IEC 801-6 which suggest a
noise immunity of up to 10 Vrms between
150 kHz and 250 MHz. At these levels, the
10 kHz tone detector in the T7256 may be desen-
sitized such that tone detection is not guaranteed
on long loops. The 3300 pF was selected to pro-
vide attenuation of this common-mode noise so
that tone detector sensitivity is not adversely
affected. Since the 3300 pF capacitor was
selected based only on guidelines, it is not man-
datory, but it is recommended in applications
which may be susceptible to high levels of com-
mon-mode noise. The final decision depends on
the specific application.
As for the size of the capacitors, lab tests indicate
the following:
1. The performance of the system suffers no
degradation until the values are increased to
about 0.1
μ
F.
2. The return loss at 25 kHz increases with
increasing capacitor value.
3. The capacitor value has no effect on longitudi-
nal balance.
4. A large unbalance in the capacitor values did
not affect return loss, longitudinal balance, or
performance.
Q11:
Are there any recommended common-mode fil-
tering parts for the U-interface I suspect that our
product may have emissions problems, and I
want to include a provision for common-mode fil-
tering on the U-interface.
A11:
The only common-mode filtering parts we have
any data on are two common-mode chokes from
Pulse Engineering (
619-674-8100
) that are
intended to help protect against external com-
mon-mode noise. The part numbers are
PE-68654 (12.5 mH) and PE-68635 (4.7 mH),
and in lab experiments, no noticeable degrada-
tion in transmission performance was observed.
These chokes are typically effective in the fre-
quency range 100 kHz—1 MHz.
As far as emissions are concerned, we don’t have
a lot of data. We have seen some success with
the use of RJ-45 connectors that have integral
ferrite beads such as those from Corcom*, Inc.,
(708) 680-7400. These provide some flexibility in
that they have the same footprint as some stan-
dard RJ-45 connectors.
* Corcom is a registered trademark of Corcom, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| T7237A | Compliance with the New ETSI PSD Requirement |
| T7256A | Compliance with the New ETSI PSD Requirement |
| T7288 | CEPT/E1 Line Interface(CEPT/E1 線接口) |
| T7290A | DS1/T1/CEPT/E1 Line Interface(DS1/T1/CEPT/E1 線接口) |
| T7295-1 | E3 Integrated Line Receiver(E3 集成線接收器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7237 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compliance with the New ETSI PSD Requirement |
| T7237A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Compliance with the New ETSI PSD Requirement |
| T7240 | 制造商:TE Connectivity 功能描述: |
| T7-241A5 | 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-241B1 | 制造商:OTTO 功能描述:Toggle Switches ON NONE ON 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None ON DPDT Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads |
發布緊急采購，3分鐘左右您將得到回復。