- 您現在的位置：買賣IC網 > PDF目錄383876 > T7234A Compliance with the New ETSI PSD Requirement PDF資料下載
參數資料
| 型號： | T7234A |
| 英文描述： | Compliance with the New ETSI PSD Requirement |
| 中文描述： | 符合新的ETSI PSD的要求 |
| 文件頁數： | 65/116頁 |
| 文件大?。?/td> | 1056K |
| 代理商： | T7234A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
January 1998
T7256 Single-Chip NT1 (SCNT1) Transceiver
Lucent Technologies Inc.
61
Application Briefs
(continued)
D-Channel Priority
(continued)
Activation Control
Because there is no guarantee that a TE will be con-
nected in this application, the local microprocessor
must be provisioned to perform a layer-1 activation
request as follows:
1. Write AUTOACT = 0 (register GR0, bit 6) to initiate
start-up on the U-interface. This results in XACT = 1
(register CFR1, bit 1). The AUTOACT bit will be set
to a 1 automatically after the start-up request is
made. This permits another activation attempt by
writing AUTOACT = 0 again (without first writing it
back to 1) if the start-up attempt fails.
A switch-initiated start-up is detected by the local
microprocessor when XACT = 1 (register CFR1, bit
1). This event can be indicated by an interrupt (INT,
pin 11) by writing the interrupt mask bit OUSCM = 0
(register UIR1, bit 3) and calling the interrupt routine
when UINT = 1 (register GIR0, bit 0). The OUSC
interrupt (register UIR0, bit 3) indicates a bit change
in either CFR1 or CFR2. Read these registers to
determine which of these bits has changed since
the last read.
In either of the above cases, it may be necessary to
set the sai[1:0] bits in register GR1 to 01. This has
the effect of indicating S/T-interface activity to the
switch even when no TE is attached. Some switches
require the reception of sai = 1 in order to properly
establish layer 1 transparency.
2. Look for XACT = 0 or OOF = 1 (register CFR1, bits
1 and 2). These events can be indicated by an inter-
rupt INT, pin 11) in a similar manner as described in
(1) above.
3. If XACT = 0, the start-up attempt has failed and
appropriate action should be taken depending on
the system requirements (it may be desirable to
attempt another start-up).
4. If OOF = 1, U-interface synchronization is complete.
Set ACTT = 1 (register GR1, bit 4). This will set the
upstream ACT = 1 on the U-interface independent
of actions on the S/T-interface. It may be desirable
to delay several tens of milliseconds between
detecting OOF and setting ACTT = 1 to allow the
S/T-interface time to activate if there is a TE present.
If this is the case, the upstream act bit will automati-
cally be set, but manually setting ACTT = 1 is per-
missible.
5. After setting ACTT = 1, wait for ACTR = 1 (register
CFR1, bit 0). This event can be indicated by an
interrupt (INT, pin 11) in a similar manner as
described in (1) above. The reception of ACTR = 1,
enables U-interface transparency in the upstream
direction, so it is not necessary to do so explicitly by
setting XPCY = 0 (register GR1, bit 5).
At this point, layer-1 activation is complete. Note that
the above steps 1—5 occur automatically if there is a
TE connected or if the LT starts up and sends an eoc
loopback-2 request (2B+D loopback). However, having
the microprocessor perform these steps ensures layer
1 activation independently of the presence of a TE.
After layer 1 activation is complete, the XACT bit (regis-
ter CFR1, bit 1) can be monitored for a state change to
0. This provides an indication to the local microproces-
sor that layer 1 has deactivated. When this occurs, set
ACTT = 0 (register GR1, bit 4) to prepare for the next
start-up attempt.
相關PDF資料 |
PDF描述 |
|---|---|
| T7237A | Compliance with the New ETSI PSD Requirement |
| T7256A | Compliance with the New ETSI PSD Requirement |
| T7288 | CEPT/E1 Line Interface(CEPT/E1 線接口) |
| T7290A | DS1/T1/CEPT/E1 Line Interface(DS1/T1/CEPT/E1 線接口) |
| T7295-1 | E3 Integrated Line Receiver(E3 集成線接收器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7237 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compliance with the New ETSI PSD Requirement |
| T7237A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Compliance with the New ETSI PSD Requirement |
| T7240 | 制造商:TE Connectivity 功能描述: |
| T7-241A5 | 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-241B1 | 制造商:OTTO 功能描述:Toggle Switches ON NONE ON 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None ON DPDT Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads |
發布緊急采購，3分鐘左右您將得到回復。