- 您現在的位置：買賣IC網 > PDF目錄383876 > T7234A Compliance with the New ETSI PSD Requirement PDF資料下載
參數資料
| 型號： | T7234A |
| 英文描述： | Compliance with the New ETSI PSD Requirement |
| 中文描述： | 符合新的ETSI PSD的要求 |
| 文件頁數： | 53/116頁 |
| 文件大?。?/td> | 1056K |
| 代理商： | T7234A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
January 1998
T7256 Single-Chip NT1 (SCNT1) Transceiver
Lucent Technologies Inc.
49
S/T-Interface Multiframing Controller
Description
If an external microprocessor is available, the T7256
can provide the capability of supporting multiframing as
defined in ITU-T I.430 Section 6.3.3 and ANSI T1.605
Section 7.3.3. Multiframing provides layer-1 signaling
capability between the TEs and the NT in both direc-
tions through the use of extra channels referred to as
the S channel for the NT-to-TE direction and the Q
channel for the TE-to-NT direction (see Figure 8 in this
data sheet for the location of the S and Q bits in the NT
and TE frames). This signaling capability is similar to
the eoc channel between the LT and NT on the U-inter-
face. The S and Q channels exist only between the TE
and NT, and there is no requirement that the NT trans-
fers this information to the U-interface.
The requirement for multiframing capability is treated
somewhat differently in ANSI T1.605, ITU-T I.430, and
ETSI ETS 300 012. The ANSI standard states that the
use of the S- and Q-channels is optional (Section
7.3.3). NTs that do not support these channels are not
required to encode the FA and M bits as required for
multiframing. TEs that do not support these channels
still must provide for identification of the Q-bit positions
and, if identified, must set each Q bit to a binary one.
ANSI defines a set of Q-channel messages, and
divides the S channel into five subchannels, defining
messages for S subchannels 1 and 2 (see T1.605
Tables 8 and 9).
ITU-T I.430 contains similar requirements for the S and
Q channels as T1.605, with the following exceptions:
1. There is no "far-end code violation" message for S
subchannel 1 (see ITU-T I.430, Table 9).
2. S subchannel 2 is not defined.
ETSI ETS 300 012 deviates slightly from ITU-T I.430. It
states that the NT1 will not provide multiframing, and
therefore the FA bit from NT-to-TE must be set to zero
(Table A.1, subclause A.6.3.3). An NT2, however, may
optionally provide multiframing in accordance with ITU-
T I.430. In either case, the TEs must provide for identifi-
cation of the Q-bit positions.
The multiframing mechanism in the T7256 is controlled
by the microprocessor. Normally, multiframing is dis-
abled (the NT transmits all zeros in the FA and M bit
positions and all ones in the S bit positions). To enable
multiframing, set MULTIF = 0 in bit 5 of register GR0.
Note that multiframing should only be enabled after the
TE interface is fully active (i.e., transmitting INFO3). In
order to guarantee this, the controller should implement
the following procedure:
1. Initialize MULTIF = 1 (this is the default on pow-
erup).
2. Monitor ACTR (register CFR1, bit 0) with the micro-
processor to detect when the system has activated
and has received INFO3. ACTR reflects the state of
the U-interface act bit from the LT, and is sent by the
LT in response to a reception of the act bit from the
NT. The NT sets act = 1 only after receiving INFO3
on the S/T-interface; so waiting for ACTR = 1
ensures that INFO3 is being received.
The monitoring of the ACTR bit can be interrupt-
driven using the ACTSC bit in interrupt register
UIR0.
3. When ACTR = 1 is detected, set MULTIF = 0 to
enable multiframing.
4. Monitor for a change from XACT = 1 to XACT = 0.
This can also be interrupt-driven using the ACTSC
bit in interrupt register UIR0.
5. When XACT = 0 is detected, this indicates that the
system has deactivated.
At this point, go back to step #1 and repeat the proce-
dure.
相關PDF資料 |
PDF描述 |
|---|---|
| T7237A | Compliance with the New ETSI PSD Requirement |
| T7256A | Compliance with the New ETSI PSD Requirement |
| T7288 | CEPT/E1 Line Interface(CEPT/E1 線接口) |
| T7290A | DS1/T1/CEPT/E1 Line Interface(DS1/T1/CEPT/E1 線接口) |
| T7295-1 | E3 Integrated Line Receiver(E3 集成線接收器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7237 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compliance with the New ETSI PSD Requirement |
| T7237A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Compliance with the New ETSI PSD Requirement |
| T7240 | 制造商:TE Connectivity 功能描述: |
| T7-241A5 | 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-241B1 | 制造商:OTTO 功能描述:Toggle Switches ON NONE ON 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None ON DPDT Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads |
發布緊急采購，3分鐘左右您將得到回復。