- 您現在的位置：買賣IC網 > PDF目錄98081 > SII3531ACNU PCI BUS CONTROLLER, QCC48 PDF資料下載
參數資料
| 型號： | SII3531ACNU |
| 元件分類： | 總線控制器 |
| 英文描述： | PCI BUS CONTROLLER, QCC48 |
| 封裝： | 7 X 7 MM, 0.40 MM PITCH, LEAD FREE, QFN-48 |
| 文件頁數： | 24/81頁 |
| 文件大?。?/td> | 532K |
| 代理商： | SII3531ACNU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
PCI Express to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
2006 Silicon Image, Inc.
SiI-DS-0208-C
30
5.3.8
PACKET Command PRB Structure
Table 5-7 shows the layout for PACKET commands. The Control and protocol override fields must be populated as described
above. The PACKET PRB FIS area is structured the same as a standard ATA command. The FIS area contains the PACKET
ATA command. After the initial PACKET command is transmitted, the device will respond with a “PIO Setup” FIS, requesting a
12 or 16-byte ATAPI command. The host driver must populate the area normally used for the first SGE with the desired
ATAPI command. The length of the ATAPI command is determined by the value of the packet length bit (Port Control, bit 5).
If packet length is 0, 12 bytes will be transmitted. If packet length is one, 16 bytes will be transmitted. The packet length field
must be initialized with the packet length value returned by the device in the IDENTIFY PACKET command. Table 5-7 shows
a representative 12-byte ATAPI command layout. The highlighted ATAPI packet is an example typical of some commands;
other command packets will have different formats within the highlighted bytes.
31
0
Protocol Override
Control
0x00
Received Transfer Count
0x04
Features / Error
Command / Status
C
R
PMP
FIS Type
0x08
Dev/Head
Cyl High
Cyl Low
Sector Number
0x0C
Features (Exp)
Cyl High (Exp)
Cyl Low (Exp)
Sector Num (Exp)
0x10
Device Control
Reserved
Sector Count (Exp)
Sector Count
0x14
Reserved
0x18
Reserved – Must Be Zero
0x1C
LBA
LBA (MSB)
Reserved
ATAPI opcode
0x20
XFR Length (MSB)
Reserved
LBA (LSB)
LBA
0x24
Reserved
XFR Length (LSB)
0x28
Reserved
0x2C
SGE1 Data Address Low
0x30
SGE1 Data Address High
0x34
SGE1Data Count
0x38
SGE1 TRM
SGE1 LNK
SGE1 DRD
SGE1 XCF
Reserved[27:0]
0x3C
Table 5-7 Port Request Block For PACKET Command
The SiI3531A does not decode the ATAPI command to determine the necessity or direction of any associated data transfer.
The host driver must supply this information by setting control_packet_read (control field, bit4) or control_packet_write (control
field, bit 5) for any PACKET command that requires data transfer. Failure to set one of these bits for an ATAPI command that
requests data transfer will result in an Overrun or Underrun Command Error condition.
相關PDF資料 |
PDF描述 |
|---|---|
| SIO10N268-NU | MULTIFUNCTION PERIPHERAL, PQFP128 |
| SIS300 | GRAPHICS PROCESSOR, PBGA365 |
| SK12430PJT | 800 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| SK12439PJ | 800 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| SK12439PJT | 800 MHz, OTHER CLOCK GENERATOR, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII3611 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:SATALink Device Bridge |
| SII3611CT80-1.5 | 制造商:SILICON IMAGE 功能描述:3611CT80-1.5 |
| SII3723 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:Third Generation SATA Port Multiplier Storage Processor |
| SiI3723CNU | 制造商:Silicon Image Inc 功能描述: |
| SII3726 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:SATA Port Multiplier |
發布緊急采購，3分鐘左右您將得到回復。