參數資料
型號： PSD913F2
英文描述： 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA7260 with optional Total Dose Rating of 300kRads
中文描述： 可配置的存儲系統級芯片的8位微控制器
文件頁數： 49/94頁
文件大?。?/td> 463K
代理商： PSD913F2
PSD913F1
Preliminary
48
The
PSD913F1
Functional
Blocks
(cont.)
9.4.2.4 Address In Mode
For microcontrollers that have more than 16 address lines, the higher addresses can be
connected to Port A, B, C, and D. The address input can be latched by the address strobe
(ALE/AS). Any input that is included in the DPLD equations for the Main Flash, Secondary
Flash, or SRAM is considered to be an address input.
9.4.2.5 Data Port Mode
Port A can be used as a data bus port for a microcontroller with a non-multiplexed
address/data bus. The Data Port is connected to the data bus of the microcontroller. The
general I/O functions are disabled in Port A if the port is configured as a Data Port.
9.4.2.6 JTAG ISP
Port C is JTAG compliant, and can be used for In-System Programming (ISP). For more
information on the JTAG Port, refer to section 9.6.
9.4.2.3 Address Out Mode
For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used
to drive latched addresses onto the port pins. These port pins can, in turn, drive external
devices. Either the output enable or the corresponding bits of both the Direction Register
and Control Register must be set to a
‘
1
’
for pins to use Address Out Mode. This must be
done by the MCU at run-time. See Table 19 for the address output pin assignments on
Ports A and B for various MCUs.
For non-multiplexed 8 bit bus mode, address lines A[7:0] are available to Port B in Address
Out Mode.
Note:
Do not drive address lines with Address Out Mode to an external memory device if it
is intended for the MCU to boot from the external device. The MCU must first boot from
PSD memory so the Direction and Control register bits can be set.
Microcontroller
Port A (3:0)
Port A (7:4)
Port B (3:0)
Port B (7:4)
8051XA (8-Bit)
80C251
(Page Mode)
N/A*
N/A
Address (7:4)
N/A
Address (11:8)
Address (11:8)
N/A
Address (15:12)
All Other
8-Bit Multiplexed
8-Bit
Non-Multiplexed Bus
Address (3:0)
Address (7:4)
Address (3:0)
Address (7:4)
N/A
N/A
Address [3:0]
Address [7:4]
Table 19. I/OPort Latched Address Output Assignments
N/A = Not Applicable.
相關PDF資料
PDF描述
PSD913F2V 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA7260 with Standard Packaging
PSD913F2(中文) Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD934F2(中文) Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD913F2 Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD934F2 Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
相關代理商/技術參數
參數描述
PSD913F2-12B81 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12B81I 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*