參數資料
型號： PSD913F2
英文描述： 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA7260 with optional Total Dose Rating of 300kRads
中文描述： 可配置的存儲系統級芯片的8位微控制器
文件頁數： 20/94頁
文件大小： 463K
代理商： PSD913F2
Preliminary
PSD913F1
19
The
PSD913F1
Functional
Blocks
(cont.)
9.1.1.4 Power Down Instruction and Power Up Condition
9.1.1.4.1 EEPROM Power Down Instruction
The EEPROM can enter power down mode with the help of the EEPROM power down
instruction (see Table 9). Once the EEPROM power down instruction is decoded, the
EEPROM memory cannot be accessed unless a Return instruction (also in Table 9) is
decoded. Alternately, this power down mode will automatically occur when the APD circuit
is triggered (see section 9.5.1). Therefore, this instruction is not required if the APD circuit is
used.
9.1.1.4.2 Power-Up Condition
The PSD913F1 Flash memory is reset upon power-up to the read array mode. Any write
operation to the EEPROM is inhibited during the first 5 msec following power-up. The FSi
and EESi select signals, along with the write strobe signal, must be in the false state during
power-up for maximum security of the data contents and to remove the possibility of a byte
being written on the first edge of a write strobe signal. Any write cycle initiation is locked
when V
CC
is below VLKO.
9.1.1.5 Read
Under typical conditions, the microcontroller may read the Flash or EEPROM memory
using read operations just as it would a ROM or RAM device. Alternately, the microcontoller
may use read operations to obtain status information about a program or erase operation in
progress. Lastly, the microcontroller may use instructions to read special data from these
memories. The following sections describe these read functions.
9.1.1.5.1 Read the Contents of Memory
Main Flash is placed in the read array mode after power-up, chip reset, or a Reset Flash
instruction (see Table 9). The microcontroller can read the memory contents of main
Flash or EEPROM by using read operations any time the read operation is not part of an
instruction sequence.
9.1.1.5.2 Read the Main Flash Memory Identifier
The main Flash memory identifier is read with an instruction composed of 4 operations:
3 specific write operations and a read operation (see Table 9). During the read operation,
address bits A6, A1, and A0 must be 0,0,1, respectively, and the appropriate sector select
signal (FSi) must be active. The Flash ID is E3h for the PSD913F1. The MCU can read the
ID only when it is executing from the EEPROM.
9.1.1.5.3 Read the Main Flash Memory Sector Protection Status
The main Flash memory sector protection status is read with an instruction composed of 4
operations: 3 specific write operations and a read operation (see Table 9). During the read
operation, address bits A6, A1, and A0 must be 0,1,0, respectively, while the chip select FSi
designates the Flash sector whose protection has to be verified. The read operation will
produce 01h if the Flash sector is protected, or 00h if the sector is not protected.
The sector protection status for all NVM blocks (main Flash or EEPROM) can be read by
the microcontroller accessing the Flash Protection and PSD/EE Protection registers in PSD
I/O space. See section 9.1.1.9.1 for register definitions.
相關PDF資料
PDF描述
PSD913F2V 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA7260 with Standard Packaging
PSD913F2(中文) Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD934F2(中文) Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD913F2 Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD934F2 Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
相關代理商/技術參數
參數描述
PSD913F2-12B81 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12B81I 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F2-12JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*