- 您現在的位置：買賣IC網 > PDF目錄368267 > PSD913F2 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA7260 with optional Total Dose Rating of 300kRads PDF資料下載
參數資料
| 型號： | PSD913F2 |
| 英文描述： | 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA7260 with optional Total Dose Rating of 300kRads |
| 中文描述： | 可配置的存儲系統級芯片的8位微控制器 |
| 文件頁數： | 48/94頁 |
| 文件大?。?/td> | 463K |
| 代理商： | PSD913F2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
Preliminary
PSD913F1
47
The
PSD913F1
Functional
Blocks
(cont.)
Control
Register
Setting
at Run-Time
Direction
Register
Setting
at Run-Time
Defined In
PSDsoft
Mode
MCU I/O
Declare pins only
0
1=output,
0=input,
PLD I/O
Logic or chip
select equations
NA
Data Port
(Port A)
Selected for MCU
with non-mux bus
NA
NA
Address Out
(Port A,B)
Declare pins only
1
1
Address In
(Port A,B,C,D)
Declare pins only
NA
NA
JTAG ISP
Declare pins only
NA
NA
Table 18. Port Operating Mode Settings
*
NA = Not Applicable
9.4.2.1 MCU I/OMode
In the MCU I/O Mode, the microcontroller uses the PSD913F1 ports to expand its own
I/O ports. By setting up the CSIOP space, the ports on the PSD913F1 are mapped into the
microcontroller address space. The addresses of the ports are listed in Table 7.
A port pin can be put into MCU I/O mode by writing a
‘
0
’
to the corresponding bit in the
Control Register. The MCU I/O direction may be changed by writing to the corresponding
bit in the Direction Register. See the subsection on the Direction Register in the
“
Port
Registers
”
section. When the pin is configured as an output, the content of the Data Out
Register drives the pin. When configured as an input, the microcontroller can read the port
input through the Data In buffer.
Ports C and D do not have Control Registers, and are in MCU I/O mode by default. They
can be used for PLD I/O if they are specified in PSDsoft.
9.4.2.2 PLD I/OMode
The PLD I/O Mode uses a port as an input to the PLDs, and/or as an output from the
GPLD. The corresponding bit in the Direction Register must not be set to
‘
1
’
if the pin is
defined as a PLD input pin in PSDsoft. The PLD I/O Mode is specified in PSDsoft by declar-
ing the port pins, and then specifying an equation in PSDsoft.
相關PDF資料 |
PDF描述 |
|---|---|
| PSD913F2V | 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA7260 with Standard Packaging |
| PSD913F2(中文) | Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統) |
| PSD934F2(中文) | Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統) |
| PSD913F2 | Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統) |
| PSD934F2 | Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD913F2-12B81 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD913F2-12B81I | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD913F2-12J | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD913F2-12JI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD913F2-12JIT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
發布緊急采購，3分鐘左右您將得到回復。