參數資料
型號： MC68HC11F1CPU4
廠商： Freescale Semiconductor
文件頁數： 81/158頁
文件大?。?/td> 0K
描述： IC MCU 512 EEPROM 4MHZ 80-LQFP
標準包裝： 90
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 30
程序存儲器類型： ROMless
EEPROM 大?。?/td> 512 x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.75 V ~ 5.25 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 80-LQFP
包裝： 托盤
CENTRAL PROCESSING UNIT
TECHNICAL DATA
3-5
When an interrupt is recognized, the current instruction finishes normally, the return
address (the current value in the program counter) is pushed onto the stack, all of the
CPU registers are pushed onto the stack, and execution continues at the address
specified by the vector for the interrupt. At the end of the interrupt service routine, an
RTI instruction is executed. The RTI instruction causes the saved registers to be pulled
off the stack in reverse order. Program execution resumes at the return address.
There are instructions that push and pull the A and B accumulators and the X and Y
index registers. These instructions are often used to preserve program context. For
example, pushing accumulator A onto the stack when entering a subroutine that uses
accumulator A, and then pulling accumulator A off the stack just before leaving the
subroutine, ensures that the contents of a register will be the same after returning from
the subroutine as it was before starting the subroutine.
3.1.5 Program Counter (PC)
The program counter, a 16-bit register, contains the address of the next instruction to
be executed. After reset, the program counter is initialized from one of six possible
vectors, depending on operating mode and the cause of reset.
3.1.6 Condition Code Register (CCR)
This 8-bit register contains five condition code indicators (C, V, Z, N, and H), two inter-
rupt masking bits, (I and X) and a stop disable bit (S). In the M68HC11 CPU, condition
codes are automatically updated by most instructions. For example, load accumulator
A (LDAA) and store accumulator A (STAA) instructions automatically set or clear the
N, Z, and V condition code flags. Pushes, pulls, add B to X (ABX), add B to Y (ABY),
and transfer/exchange instructions do not affect the condition codes. Refer to Table
3-2, which shows what condition codes are affected by a particular instruction.
3.1.6.1 Carry/Borrow (C)
The C bit is set if the arithmetic logic unit (ALU) performs a carry or borrow during an
arithmetic operation. The C bit also acts as an error flag for multiply and divide opera-
tions. Shift and rotate instructions operate with and through the carry bit to facilitate
multiple-word shift operations.
3.1.6.2 Overflow (V)
The overflow bit is set if an operation causes an arithmetic overflow. Otherwise, the V
bit is cleared.
Table 3-1 Reset Vector Comparison
POR or RESET Pin
Clock Monitor
COP Watchdog
Normal
$FFFE, F
$FFFC, D
$FFFA, B
Test or Boot
$BFFE, F
$BFFC, D
$BFFA, B
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HRC908JK3CDW IC MCU 4K FLASH 8MHZ SO20
MC68HC711K4CFU4 IC MCU 24K 4MHZ EEPROM 80-QFP
MC68HC11K1CFN4 IC MCU 640 EEPROM 4MHZ 84-PLCC
MC68332ACFC20B1 IC MCU 32BIT 20MHZ 132-PQFP
MC68332GCFC16 IC MCU 32BIT 16MHZ 132-PQFP
相關代理商/技術參數
參數描述
MC68HC11F1CPU5 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1CPUE5 制造商:Freescale Semiconductor 功能描述:
MC68HC11F1FB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1FB1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1FB3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*