- 您現在的位置：買賣IC網 > PDF目錄3793 > MC68HC11F1CPU4 (Freescale Semiconductor)IC MCU 512 EEPROM 4MHZ 80-LQFP PDF資料下載
參數資料
| 型號： | MC68HC11F1CPU4 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 15/158頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 512 EEPROM 4MHZ 80-LQFP |
| 標準包裝： | 90 |
| 系列： | HC11 |
| 核心處理器： | HC11 |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 連通性： | SCI，SPI |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 30 |
| 程序存儲器類型： | ROMless |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.75 V ~ 5.25 V |
| 數據轉換器： | A/D 8x8b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 80-LQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
TIMING SYSTEM
TECHNICAL DATA
9-5
9.2 Input Capture
The input capture function records the time an external event occurs by latching the
value of the free-running counter when a selected edge is detected at the associated
timer input pin. Software can store latched values and use them to compute the peri-
odicity and duration of events. For example, by storing the times of successive edges
of an incoming signal, software can determine the period and pulse width of a signal.
To measure period, two successive edges of the same polarity are captured. To mea-
sure pulse width, two alternate polarity edges are captured.
In most cases, input capture edges are asynchronous to the internal timer counter,
which is clocked relative to an internal clock (PH2). These asynchronous capture re-
quests are synchronized to PH2 so that the latching occurs on the opposite half cycle
of PH2 from when the timer counter is being incremented. This synchronization pro-
cess introduces a delay from when the edge occurs to when the counter value is de-
tected. Because these delays offset each other when the time between two edges is
being measured, the delay can be ignored. When an input capture is being used with
an output compare, there is a similar delay between the actual compare point and
when the output pin changes state.
The control and status bits that implement the input capture functions are contained in
the PACTL, TCTL2, TMSK1, and TFLG1 registers.
To configure port A bit 3 as an input capture, clear the DDA3 bit of the DDRA register.
Note that this bit is cleared out of reset. To enable PA3 as the fourth input capture, set
the I4/O5 bit in the PACTL register. Otherwise, PA3 is configured as a fifth output com-
pare out of reset, with bit I4/O5 being cleared. If the DDA3 bit is set (configuring PA3
as an output), and IC4 is enabled, then writes to PA3 cause edges on the pin to result
in input captures. Writing to TI4/O5 has no effect when the TI4/O5 register is acting as
IC4.
9.2.1 Timer Control Register 2
Use the control bits of this register to program input capture functions to detect a par-
ticular edge polarity on the corresponding timer input pin. Each of the input capture
functions can be independently configured to detect rising edges only, falling edges
only, any edge (rising or falling), or to disable the input capture function. The input cap-
ture functions operate independently of each other and can capture the same TCNT
value if the input edges are detected within the same timer count cycle.
EDGxB and EDGxA — Input Capture Edge Control
There are four pairs of these bits. Each pair is cleared to zero by reset and must be
encoded to configure the corresponding input capture edge detector circuit. IC4 func-
tions only if the I4/O5 bit in the PACTL register is set. Refer to Table 9-2 for timer con-
trol configuration.
TCTL2 — Timer Control 2
$1021
Bit 7
654321
Bit 0
EDG4B
EDG4A
EDG1B
EDG1A
EDG2B
EDG2A
EDG3B
EDG3A
RESET:
0000000
0
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HRC908JK3CDW | IC MCU 4K FLASH 8MHZ SO20 |
| MC68HC711K4CFU4 | IC MCU 24K 4MHZ EEPROM 80-QFP |
| MC68HC11K1CFN4 | IC MCU 640 EEPROM 4MHZ 84-PLCC |
| MC68332ACFC20B1 | IC MCU 32BIT 20MHZ 132-PQFP |
| MC68332GCFC16 | IC MCU 32BIT 16MHZ 132-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11F1CPU5 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11F1CPUE5 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC11F1FB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1FB1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1FB3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。