參數資料
型號： MC68HC11F1CPU4
廠商： Freescale Semiconductor
文件頁數： 107/158頁
文件大小： 0K
描述： IC MCU 512 EEPROM 4MHZ 80-LQFP
標準包裝： 90
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 30
程序存儲器類型： ROMless
EEPROM 大?。?/td> 512 x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.75 V ~ 5.25 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 80-LQFP
包裝： 托盤
OPERATING MODES AND ON-CHIP MEMORY
MC68HC11F1
4-14
TECHNICAL DATA
4.4 EEPROM and CONFIG Register
The 512-byte EEPROM array and the single-byte CONFIG register are implemented
with the same type of memory cells. The CONFIG register is a separate address lo-
cated within the register block rather than in the EEPROM array. Unlike other registers
within the register block, the CONFIG register can only be altered using the EEPROM
programming procedure.
4.4.1 EEPROM
The 512-byte on-board EEPROM is initially located from $FE00 to $FFFF after reset
in single-chip modes. It can be mapped to any other 4-Kbyte boundary by program-
ming bits EE[3:0] in the CONFIG register. The EEPROM is enabled by the EEON bit
in the CONFIG register. Programming and erasing is controlled by the PPROG regis-
ter.
Unlike information stored in ROM, data in the 512 bytes of EEPROM can be erased
and reprogrammed under software control. Because programming and erasing oper-
ations use an on-chip charge pump, a separate external power supply is not required.
Use of the block protect register (BPROT) prevents inadvertent writes to (or erases of)
blocks of EEPROM. The CSEL bit in the OPTION register selects an on-chip oscillator
clock for programming and erasing while operating at frequencies below 1 MHz.
4.4.1.1 EEPROM Programming
An exact register access sequence must be followed to allow successful programming
and erasure of the EEPROM. The following procedures for modifying the EEPROM
and CONFIG register detail the sequence. If an attempt is made to set both EELAT
and EEPGM bits in the same write cycle and this attempt occurs before the required
write cycle with the EELAT bit set, then neither bit is set. If a write to an EEPROM ad-
dress is performed while the EEPGM bit is set, the write is ignored, and the program-
ming operation in progress is not disturbed. If no EEPROM address is written between
the point at which EELAT is set and EEPGM is set, then no program or erase operation
occurs. These safeguards are included to prevent accidental EEPROM changes in
cases of program runaway. If the frequency of the E clock is 1 MHz or less, the CSEL
bit in the OPTION register must be set to select the internal RC clock.
When the EELAT bit in the PPROG register is cleared, the EEPROM can be read as
if it were a ROM. The block protect register has no effect during reads. During EE-
PROM programming, the ROW and BYTE bits of PPROG are not used.
Table 4-6 EEPROM Block Protection
Bit Name
Block Protected
Block Size
BPRT0
$xE00–$xE1F
32 Bytes
BPRT1
$xE20–$xE5F
64 Bytes
BPRT2
$xE60–$xEDF
128 Bytes
BPRT3
$xEE0–$xFFF
288 Bytes
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HRC908JK3CDW IC MCU 4K FLASH 8MHZ SO20
MC68HC711K4CFU4 IC MCU 24K 4MHZ EEPROM 80-QFP
MC68HC11K1CFN4 IC MCU 640 EEPROM 4MHZ 84-PLCC
MC68332ACFC20B1 IC MCU 32BIT 20MHZ 132-PQFP
MC68332GCFC16 IC MCU 32BIT 16MHZ 132-PQFP
相關代理商/技術參數
參數描述
MC68HC11F1CPU5 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1CPUE5 制造商:Freescale Semiconductor 功能描述:
MC68HC11F1FB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1FB1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1FB3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*