參數資料
型號： FDC37C666GT
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 存儲控制器/管理單元
英文描述： High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
中文描述： 1 Mbps, IDE COMPATIBLE, FLOPPY DISK DRIVE CONTROLLER, PQFP100
封裝： QFP-100
文件頁數： 70/152頁
文件大?。?/td> 621K
代理商： FDC37C666GT
70
Note that if implied seek is not enabled, the read
and write commands should be preceded by:
1) Seek command - Step to the proper track
2) Sense
Interrupt
Terminate the Seek command
3) Read ID - Verify head is on proper track
4) Issue Read/Write command.
Status
command
-
The Seek command does not have a result
phase. Therefore, it is highly recommended that
the Sense Interrupt Status command be issued
after the Seek command to terminate it and to
provide verification of the head position (PCN).
The H bit (Head Address) in ST0 will always
return to a "0". When exiting POWERDOWN
mode, the FDC clears the PCN value and the
status information to zero. Prior to issuing the
POWERDOWN
command,
recommended that the user service all pending
interrupts through the Sense Interrupt Status
command.
it
is
highly
Sense Interrupt Status
An interrupt signal on FINT pin is generated by
the FDC for one of the following reasons:
1. Upon entering the Result Phase of:
a. Read Data command
b. Read A Track command
c. Read ID command
d. Read Deleted Data command
e. Write Data command
f.
Format A Track command
g. Write Deleted Data command
h. Verify command
2. End of Seek, Relative Seek, or Recalibrate
command
3. FDC requires a data transfer during the
execution phase in the non-DMA mode
The Sense Interrupt Status command resets the
interrupt signal and, via the IC code and SE bit
of Status Register 0, identifies the cause of the
interrupt.
Table 30 - Interrupt Identification
IC
INTERRUPT DUE TO
11
00
Normal termination of Seek
or Recalibrate command
Abnormal termination of
Seek or Recalibrate
command
The Seek, Relative Seek, and Recalibrate
commands have no result phase. The Sense
Interrupt Status command must be issued
immediately after these commands to terminate
them and to provide verification of the head
position (PCN). The H (Head Address) bit in
ST0 will always return a "0". If a Sense Interrupt
Status is not issued, the drive will continue to be
BUSY and may affect the operation of the next
command.
Sense Drive Status
Sense Drive Status obtains drive status
information. It has not execution phase and
goes directly to the result phase from the
command phase. Status Register 3 contains
the drive status information.
Specify
The Specify command sets the initial values for
each of the three internal times. The HUT
(Head Unload Time) defines the time from the
end of the execution phase of one of the
read/write commands to the head unload state.
The SRT (Step Rate Time) defines the time
interval between adjacent step pulses. Note that
the spacing between the first and second step
pulses may be shorter than the remaining step
pulses. The HLT (Head Load Time) defines
SE
0
1
1
01
Polling
相關PDF資料
PDF描述
FDC37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
FDC37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
FDC37M600 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
FDC37M601 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
FDC37M602 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
相關代理商/技術參數
參數描述
FDC37C669 制造商:SMSC 制造商全稱:SMSC 功能描述:PC 98/99 Compliant Super I/O Floppy Disk Controller with Infrared Support
FDC37C669_07 制造商:SMSC 制造商全稱:SMSC 功能描述:PC 98/99 Compliant Super I/O Floppy Disk Controller with Infrared Support
FDC37C669FRQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk
FDC37C669FRTQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk
FDC37C669-MS 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller- Pb Free RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*