- 您現在的位置：買賣IC網 > PDF目錄381841 > FDC37C666GT (STANDARD MICROSYSTEMS CORP) High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers PDF資料下載
參數資料
| 型號： | FDC37C666GT |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 存儲控制器/管理單元 |
| 英文描述： | High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
| 中文描述： | 1 Mbps, IDE COMPATIBLE, FLOPPY DISK DRIVE CONTROLLER, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 62/152頁 |
| 文件大小： | 621K |
| 代理商： | FDC37C666GT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁
62
DATA TRANSFER COMMANDS
All of the Read Data, Write Data and Verify type
commands use the same parameter bytes and
return the same results information, the only
difference being the coding of bits 0-4 in the first
byte.
An implied seek will be executed if the feature
was enabled by the Configure command. This
seek is completely transparent to the user. The
Drive Busy bit for the drive will go active in the
Main Status Register during the seek portion of
the command. If the seek portion fails, it will be
reflected in the results status normally returned
for a Read/Write Data command. Status
Register 0 (ST0) would contain the error code
and C would contain the cylinder on which the
seek failed.
Read Data
A set of nine (9) bytes is required to place the
FDC in the Read Data Mode. After the Read
Data command has been issued, the FDC loads
the head (if it is in the unloaded state), waits the
specified head settling time (defined in the
Specify command), and begins reading ID
Address Marks and ID fields. When the sector
address read off the diskette matches with the
sector address specified in the command, the
FDC reads the sector's data field and transfers
the data to the FIFO.
After completion of the read operation from the
current
sector,
the
incremented by one and the data from the next
logical sector is read and output via the FIFO.
This continuous read function is called "Multi-
Sector Read Operation". Upon receipt of TC, or
an implied TC (FIFO overrun/underrun), the
FDC stops sending data but will continue to
read data from the current sector, check the
CRC bytes, and at the end of the sector,
terminate the Read Data Command.
sector
address
is
N determines the number of bytes per sector
(see Table 23 below). If N is set to zero, the
sector size is set to 128. The DTL value
determines the number of bytes to be
transferred. If DTL is less than 128, the FDC
transfers the specified number of bytes to the
host. For reads, it continues to read the entire
128-byte sector and checks for CRC errors. For
writes, it completes the 128-byte sector by filling
in zeros. If N is not set to 00 Hex, DTL should
be set to FF Hex and has no impact on the
number of bytes transferred.
Table 23 - Sector Sizes
SECTOR SIZE
The amount of data which can be handled with
a single command to the FDC depends upon
MT (multi-track) and N (number of bytes/sector).
The Multi-Track function (MT) allows the FDC to
read data from both sides of the diskette. For a
particular cylinder, data will be transferred
starting at Sector 1, Side 0 and completing the
last sector of the same track at Side 1.
If the host terminates a read or write operation
in the FDC, the ID information in the result
phase is dependent upon the state of the MT bit
and EOT byte. Refer to Table 24.
At the completion of the Read Data command,
the head is not unloaded until after the Head
Unload Time Interval (specified in the Specify
command) has elapsed. If the host issues
another command before the head unloads,
then the head settling time may be saved
between subsequent reads.
N
00
01
02
03
..
07
128 bytes
256 bytes
512 bytes
1024 bytes
...
16 Kbytes
相關PDF資料 |
PDF描述 |
|---|---|
| FDC37C67X | ENHANCED SUPER I/O CONTROLLER WITH FAST IR |
| FDC37C957FR | ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS |
| FDC37M600 | ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT |
| FDC37M601 | ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT |
| FDC37M602 | ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FDC37C669 | 制造商:SMSC 制造商全稱:SMSC 功能描述:PC 98/99 Compliant Super I/O Floppy Disk Controller with Infrared Support |
| FDC37C669_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:PC 98/99 Compliant Super I/O Floppy Disk Controller with Infrared Support |
| FDC37C669FRQFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| FDC37C669FRTQFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| FDC37C669-MS | 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller- Pb Free RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。