參數資料
型號： EVAL-ADUC7036QSPZ
廠商： Analog Devices Inc
文件頁數： 75/132頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR ADUC7036
設計資源： EVAL-ADUC7036 Schematic & Brd Outline
EVAL ADUC7036 Gerber Files
標準包裝： 1
系列： QuickStart™ PLUS 套件
主要目的： 電源管理，電池監控器
嵌入式： 是，MCU，16/32 位
已用 IC / 零件： ADuC7036
已供物品： 板，線纜，文檔，仿真器，電源，軟件
ADuC7036
Rev. C | Page 47 of 132
ADC Interrupt Mask Register
Name: ADCMSKI
Address: 0xFFFF0504
Default Value: 0x00
Access: Read/write
Function: This register allows the ADC interrupt sources to be individually enabled. The bit positions in this register are the same as the
lower eight bits in the ADCSTA MMR. If a bit is set by user code to 1, the respective interrupt is enabled. By default, all bits are 0,
meaning all ADC interrupt sources are disabled.
ADC Mode Register
Name: ADCMDE
Address: 0xFFFF0508
Default Value: 0x00
Access: Read/write
Function: This 8-bit register configures the mode of operation of the ADC subsystem.
Table 36. ADCMDE MMR Bit Designations
Bit
Description
7
Not used. This bit is reserved for future functionality and should be written as 0 by user code.
6
20 kΩ resistor select.
Set to 1 to select the 20 kΩ resistor as shown in Figure 21.
Set to 0 to select the direct path to ground as shown in Figure 21 (default).
5
Low power mode reference select.
Set to 1 to enable the precision voltage reference in either low power mode or low power plus mode, thereby increasing current
consumption.
Set to 0 to enable the low power voltage reference in either low power mode or low power plus mode (default).
4 to 3
ADC power mode configuration.
00 = ADC normal mode. If enabled, the ADC operates with normal current consumption yielding optimum electrical performance.
01 = ADC low power mode. If enabled, the I-ADC operates with reduced current consumption. This limitation in current
consumption is achieved (at the expense of ADC noise performance) by fixing the gain to 128 and using the on-chip low power
(131 kHz) oscillator to directly drive the ADC circuits.
10 = ADC low power plus mode. If enabled, the ADC operates with reduced current consumption. In this mode, the gain is fixed to
512 and the current consumed is approximately 200 μA more than the ADC low power mode. The additional current consumed
also ensures that the ADC noise performance is better than that achieved in ADC low power mode.
11 = not defined.
2 to 0
ADC operation mode configuration.
000 = ADC power-down mode. All ADC circuits (including internal reference) are powered down.
001 = ADC continuous conversion mode. In this mode, any enabled ADC continuously converts.
010 = ADC single conversion mode. In this mode, any enabled ADC performs a single conversion. The ADC enters idle mode when
the single shot conversion is complete. A single conversion takes two to three ADC clock cycles depending on the chop mode.
011 = ADC idle mode. In this mode, the ADC is fully powered on but is held in reset.
100 = ADC self-offset calibration. In this mode, an offset calibration is performed on any enabled ADC using an internally
generated 0 V. The calibration is carried out at the user programmed ADC settings; therefore, as with a normal single ADC
conversion, it takes two to three ADC conversion cycles before a fully settled calibration result is ready. The calibration result is
automatically written to the ADCxOF MMR of the respective ADC. The ADC returns to idle mode and the calibration and
conversion ready status bits are set at the end of an offset calibration cycle.
101 = ADC self-gain calibration. In this mode, a gain calibration against an internal reference voltage is performed on all enabled
ADCs. A gain calibration is a two-stage process and takes twice the time of an offset calibration. The calibration result is
automatically written to the ADCxGN MMR of the respective ADC. The ADC returns to idle mode, and the calibration and
conversion ready status bits are set at the end of a gain calibration cycle. An ADC self-gain calibration should only be carried out
on the current channel ADC. Preprogrammed, factory calibration coefficients (downloaded automatically from internal Flash/EE)
should be used for voltage temperature measurements. If an external NTC is used, an ADC self-calibration should be performed
on the temperature channel.
110 = ADC system zero-scale calibration. In this mode, a zero-scale calibration is performed on enabled ADC channels against an
external zero-scale voltage driven at the ADC input pins. The calibration is carried out at the user programmed ADC settings;
therefore, as with a normal, single ADC conversion, it takes three ADC conversion cycles before a fully settled calibration result is ready.
111 = ADC system full-scale calibration. In this mode, a full-scale calibration is performed on enabled ADC channels against an
external full-scale voltage driven at the ADC input pins.
相關PDF資料
PDF描述
EVB90308 DEMO KIT MLX90308 SENS INTERFACE
MLG0603S4N7S INDUCTOR MULTILAYER 4.7NH 0201
KSZ8041TL-EVAL BOARD EVALUATION KSZ8041TL
EEU-FR1J180 CAP ALUM 18UF 63V 20% RADIAL
MLG0603S3N6S INDUCTOR MULTILAYER 3.6NH 0201
相關代理商/技術參數
參數描述
EVAL-ADUC7039QSPZ 功能描述:BOARD EVAL FOR ADUC7039 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7060QSPZ 功能描述:KIT DEV QUICK START ADUC7060 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7060QSPZU1 制造商:Analog Devices 功能描述:
EVALADUC7060QSPZU2 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Boxed Product (Development Kits)
EVAL-ADUC7061MKZ 功能描述:開發板和工具包 - ARM Quick Start Development System RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*