參數資料
型號: CDB8952
廠商: Cirrus Logic, Inc.
英文描述: CrystalLAN 100BASE-X and 10BASE-T Transceiver
中文描述: CrystalLAN個100Base - X和10Base - T的收發器
文件頁數: 45/82頁
文件大小: 1130K
代理商: CDB8952
CS8952
CrystalLAN
100BASE-X and 10BASE-T Transceiver
45
6.10
Interrupt Status Register - Address 11h
This register indicates which event(s) caused an interrupt event on the MII_IRQ pin. All bits are self-
clearing, and will thus be cleared upon readout.
15
14
13
12
11
10
9
8
CIM Link
Unstable
Link Status
Change
Descrambler
Lock Change
PrematureEnd
Error
DCR
Rollover
FCCR
Rollover
RECR
Rollover
Remote
Loopback
Fault
7
6
5
4
3
2
1
0
Reset
Complete
Jabber
Detect
Auto-Neg
Complete
Parallel
Detection Fault
Parallel
Fail
Remote
Fault
Page
Received
Reserved
BIT
15
NAME
TYPE
RESET
DESCRIPTION
CIM Link Unstable
Read Only
0
When set, this bit indicates that an unstable link con-
dition was detected by the Carrier Integrity Monitor
function.
When set, this bit indicates that a change has
occurred to the status of the link. The Self Status
Register (address 19h) may be read to determine the
current status of the link.
When set, this bit indicates that a change has
occurred in the status of the descrambler. The Self
Status Register (address 19h) may be read to deter-
mine the current status of the scrambler lock.
This bit is set when a premature end of frame is
detected for 100 Mb/s operation. A premature end is
defined as two consecutive IDLE patterns detected in
a frame prior to the End of Stream Delimiter.
This bit is set when the MSB of the Disconnect Count
Register (address 12h) becomes set. This should
provide ample warning to the management layer so
that the DCR may be read before rolling over.
This bit is set when the MSB of the False Carrier
Count Register (address 13h) becomes set. This
should provide ample warning to the management
layer so that the FCCR may be read before saturat-
ing.
This bit is set when the MSB of the Receive Error
Count Register (address 15h) becomes set. This
should provide ample warning to the management
layer so that the RECR may be read before rolling
over.
14
Link Status Change Read Only
0
13
Descrambler Lock
Change
Read Only
0
12
Premature End
Error
Read Only
0
11
DCR Rollover
Read Only
0
10
FCCR Rollover
Read Only
0
9
RECR Rollover
Read Only
0
相關PDF資料
PDF描述
CDBH38D18 POWER INDUCTORS
CDBM128 POWER INDUCTORS
CDBM73MN POWER INDUCTORS
CDBM7D28 POWER INDUCTORS
CDC112 1-Line To 9-Line Differential LVPECL Clock Driver(1線-9線差分 LVPECL時鐘驅動器)
相關代理商/技術參數
參數描述
CDB8952T 功能描述:以太網開發工具 Eval Bd 100BASE-TX/ 10BASE-T Transceiver RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
CDB-9PF 制造商:HRS 制造商全稱:HRS 功能描述:CD CRIMP TYPE CONNECTOR
CDB-9SF 制造商:HRS 制造商全稱:HRS 功能描述:CD CRIMP TYPE CONNECTOR
CDBA1100 制造商:COMCHIP 制造商全稱:Comchip Technology 功能描述:SMD Schottky Barrier Rectifier
CDBA1100-G 功能描述:肖特基二極管與整流器 SCHOTTKY DIODE 1A, 100V RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel