參數資料
型號: CDB8952
廠商: Cirrus Logic, Inc.
英文描述: CrystalLAN 100BASE-X and 10BASE-T Transceiver
中文描述: CrystalLAN個100Base - X和10Base - T的收發器
文件頁數: 21/82頁
文件大?。?/td> 1130K
代理商: CDB8952
CS8952
CrystalLAN 100BASE-X and 10BASE-T Transceiver
21
rupt signal to the controller when a change of state
has occurred in the CS8952, eliminating the need
for the system to poll the CS8952 for state changes.
The RX_EN signal allows the receiver outputs to
be electrically isolated. The ISODEF pin controls
the value of register bit ISOLATE in the Basic
Mode Control Register (address 00h) which in turn
electrically isolates the CS8952's MII data path.
3.1
The following sections describe the four major op-
erating modes of the CS8952:
Major Operating Modes
-
100BASE-X MII Modes (TX and FX)
-
100BASE-X Repeater Modes
-
10BASE-T MII Mode
-
10BASE-T Serial Mode
The choice of operating speed (10 Mb/s versus
100 Mb/s) is made using the auto-negotiation input
pins (AN0, AN1) and/or the auto-negotiation MII
registers. The auto-negotiation capability also is
used to select a duplex mode (full or half duplex).
Both speed and duplex modes can either be forced
or negotiated with the far-end link partner.
The digital interface mode (MII, repeater, or
10BASE-T serial) is selected by input pins
BPALIGN, BP4B5B and 10BT_SER as shown in
Table
1
. Speed and duplex selection are made
through the AN[1:0] pins as shown in Table
5
.
3.1.1
100BASE-X MII Application (TX
and FX)
The CS8952 provides an IEEE 802.3-compliant
MII interface. Data is transferred across the MII in
four-bit parallel (nibble) mode. TX_CLK and
RX_CLK are nominally 25 MHz for 100BASE-X.
The 100BASE-X mode includes both the TX and
FX modes, as determined by pin BPSCR (bypass
scrambler), or the BPSCR bit (bit 13) in the Loop-
back, Bypass, and Receiver Error Mask Register
(address 18h). In FX mode, an external optical
module is connected to the CS8952 via pins
TX_NRZ+, TX_NRZ-, RX_NRZ+, RX_NRZ-,
SIGNAL+, and SIGNAL-. In FX mode, the MLT-
3/NRZI conversion blocks and the scrambler/de-
scrambler are bypassed.
3.1.1.1
Symbol Encoding and Decoding
In 100BASE-X modes, 4-bit nibble transmit data is
encoded into 5-bit symbols for transmission onto
the media as shown in Tables
2
and
3
. The encod-
ing is necessary to allow data and control symbols
to be sent consecutively along the same media
transparent to the MAC layer. This encoding caus-
es the symbol rate transmitted across the wire (125
symbols/second) to be greater than the actual data
rate of the system (100 symbols/second).
Operating Mode BPALIGN BP4B5B
100BASE-X MII
10BASE-T MII
10BT_SER
0
0
0
0
0
0
Table 1.
100BASE-X
Repeater
1
Don
t
Care
1
Don
t
Care
0
0
0
1
10BASE-T Serial
Don
t
Care
Table 1.
Operating Mode BPALIGN BP4B5B
10BT_SER
DATA and CONTROL Codes (RX_ER = 0 or TX_ER = 0)
5-bit Symbol
4-bit Nibble
Name
Comments
DATA (Note
1
)
0
1
11110
01001
0000
0001
相關PDF資料
PDF描述
CDBH38D18 POWER INDUCTORS
CDBM128 POWER INDUCTORS
CDBM73MN POWER INDUCTORS
CDBM7D28 POWER INDUCTORS
CDC112 1-Line To 9-Line Differential LVPECL Clock Driver(1線-9線差分 LVPECL時鐘驅動器)
相關代理商/技術參數
參數描述
CDB8952T 功能描述:以太網開發工具 Eval Bd 100BASE-TX/ 10BASE-T Transceiver RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
CDB-9PF 制造商:HRS 制造商全稱:HRS 功能描述:CD CRIMP TYPE CONNECTOR
CDB-9SF 制造商:HRS 制造商全稱:HRS 功能描述:CD CRIMP TYPE CONNECTOR
CDBA1100 制造商:COMCHIP 制造商全稱:Comchip Technology 功能描述:SMD Schottky Barrier Rectifier
CDBA1100-G 功能描述:肖特基二極管與整流器 SCHOTTKY DIODE 1A, 100V RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel