- 您現在的位置：買賣IC網 > PDF目錄366552 > AM8530 (Advanced Micro Devices, Inc.) Serial Communications Controller PDF資料下載
參數資料
| 型號： | AM8530 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | Serial Communications Controller |
| 中文描述： | 串行通信控制器 |
| 文件頁數： | 44/194頁 |
| 文件大小： | 797K |
| 代理商： | AM8530 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
I/O Programming Functional Description
AMD
3–13
3.8
The External/Status Interrupts are globally enabled via WR1 and may be individually en-
abled via WR15 as shown below. The External/Status interrupt sources are: 1) Zero
Count, 2) DCD, 3) SYNC/HUNT, 4) CTS, 5) Tx Underrun/EOM, and 6) BREAK/ABORT.
EX T ERNAL/S T AT US INT ERRUPT S
D7
BREAK/
ABORT
IE
D6
Tx
Undr/
EOM IE
D5
CTS
IE
D4
SYNC/
HUNT
IE
D3
DCD
IE
D2
D1
Zero
Count
IE
D0
D7
D6
D5
D4
D3
D2
D1
D0
Ext/
Status
MIE
WR15 and WR1—Register Layout
The individual External/Status Interrupt enable bits in WR15 control whether or not
latches will be present in the path from the source of interrupt to the status bit in RR0. If
an individual enable bit in WR15 is set to ‘0’, the latches are not present in the signal path
and the value read in RR0 reflects the current status. An interrupt source whose individ-
ual enable bit in WR15 is set to ‘0’ is not a source of External/Status interrupts even
though the External/Status Master Interrupt Enable bit is set to ‘1’ in WR1 (D0). When an
individual enable bit in WR15 is set to ‘1’, the latch is present in the signal path.
The latches for the sources of External/Status interrupts are not independent. Rather,
they all close at the same time as a result of a state change by one of the sources of in-
terrupt. Thus, a read of RR0 returns the current status for any bits whose individual en-
able bit in WR15 is set to ‘0’, and either the current state or the latched state of the re-
mainder of the bits. To guarantee the current status, the processor should issue a Reset
External/Status Interrupts Command in WR0 to open the latches.
The External/Status IP in RR3 is set by the closing of the latches and remains set for as
long as they are closed. If the master External/Status Interrupt enable bit is not set, the IP
will never be set, even though the latches may be present in the signal paths and working
as described. Because the latches close on the current status but give no indication of
change, the processor must maintain a copy of RR0 in memory. When the SCC gener-
ates an External/Status interrupt, the processor should read RR0 and determine which
condition changed state and take the appropriate action. The copy of RR0 in memory
must then be updated and the Reset External/Status Interrupt Command issued.
Care must be taken in writing the interrupt service routine for the External/Status inter-
rupts because it is possible for more than one status condition to change state at the
same time. All of the latched bits in RR0 should be compared to the copy of RR0 in mem-
ory. If none have changed and the ZC interrupt is enabled, the Zero Count condition
caused the interrupt.
3.8.1
The SYNC/HUNT status bit reports the Hunt state of the receiver in SDLC and Synchro-
nous modes. This bit is set to ‘1’ when the processor issues the Enter Hunt Command,
and is reset to ‘0’ when character synchronization is established by the receiver. If the
SYNC/HUNT IE bit in WR15 is set to ‘1’, the External/Status latches close, and an Exter-
nal/Status interrupt will be generated on both the Low-to-High and High-to-Low transitions
of the SYNC/HUNT status bit.
S ync /Hunt
相關PDF資料 |
PDF描述 |
|---|---|
| AM8530H | Serial Communications Controller |
| AM85C30-10PC | Enhanced Serial Communications Controller |
| Am85C30 | Serial Communications Controller |
| AM85C30 | Enhanced Serial Communications Controller |
| AM85C30-8PC | Enhanced Serial Communications Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM8530ADC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller |
| AM8530ADCB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller |
| AM8530AJC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller |
| AM8530APC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller |
| AM8530DC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller |
發布緊急采購，3分鐘左右您將得到回復。