- 您現在的位置：買賣IC網 > PDF目錄165354 > ADSP-21060LCWZ-160 (ANALOG DEVICES INC) 48-BIT, 40 MHz, OTHER DSP, CQFP240 PDF資料下載
參數資料
| 型號： | ADSP-21060LCWZ-160 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 48-BIT, 40 MHz, OTHER DSP, CQFP240 |
| 封裝： | THERMALLY ENHANCED, METRIC, HEAT SINK, CERAMIC, QFP-240 |
| 文件頁數： | 3/48頁 |
| 文件大?。?/td> | 481K |
| 代理商： | ADSP-21060LCWZ-160 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADSP-21060C/ADSP-21060LC
–11–
REV. B
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE 1149.1
JTAG test access port of the ADSP-2106x to monitor and control
the target board processor during emulation. The EZ-ICE probe
requires the ADSP-2106x’s CLKIN, TMS, TCK,
TRST, TDI,
TDO,
EMU, and GND signals be made accessible on the target
system via a 14-pin connector (a 2 row
× 7 pin strip header) such
as that shown in Figure 5. The EZ-ICE probe plugs directly onto
this connector for chip-on-board emulation. You must add this
connector to your target board design if you intend to use the
ADSP-2106x EZ-ICE. The total trace length between the EZ-
ICE connector and the furthest device sharing the EZ-ICE
JTAG pins should be limited to 15 inches maximum for guaran-
teed operation. This length restriction must include EZ-ICE
JTAG signals that are routed to one or more ADSP-2106x
devices, or a combination of ADSP-2106x devices and other
JTAG devices on the chain.
TOP VIEW
13
14
11
12
910
9
78
56
34
12
EMU
CLKIN (OPTIONAL)
TMS
TCK
TRST
TDI
TDO
GND
KEY (NO PIN)
BTMS
BTCK
BTRST
BTDI
GND
Figure 5. Target Board Connector for ADSP-2106x EZ-ICE
Emulator (Jumpers in Place)
EMU
TRST
EMU
TRST
ADSP-2106x
#1
JTAG
DEVICE
(OPTIONAL)
ADSP-2106x
n
TDI
EZ-ICE
JTAG
CONNECTOR
OTHER
JTAG
CONTROLLER
OPTIONAL
TCK
TMS
EMU
TMS
TCK
TDO
CLKIN
TRST
TCK
TMS
TCK
TMS
TDI
TDO
TDI
TDO
TDI
Figure 6. JTAG Scan Path Connections for Multiple ADSP-2106x Systems
The 14-pin, 2-row pin strip header is keyed at the Pin 3 location —
Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1
× 0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie and Samtec.
The BTMS, BTCK,
BTRST and BTDI signals are provided so
the test access port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins. If the test
access port will not be used for board testing, tie
BTRST to GND
and tie or pull BTCK up to VDD. The
TRST pin must be
asserted after power-up (through
BTRST on the connector) or
held low for proper operation of the ADSP-2106x. None of the
Bxxx pins (Pins 5, 7, 9, 11) are connected on the EZ-ICE probe.
The JTAG signals are terminated on the EZ-ICE probe as
follows:
Signal
Termination
TMS
Driven through 22
Resistor (16 mA Driver)
TCK
Driven at 10 MHz through 22
Resistor (16 mA
Driver)
TRST* Active Low Driven through 22
Resistor (16 mA
Driver) (Pulled Up by On-Chip 20 k
Resistor)
TDI
Driven by 22
Resistor (16 mA Driver)
TDO
One TTL Load, Split Termination (160/220)
CLKIN One TTL Load, Split Termination (160/220)
EMU
Active Low 4.7 k
Pull-Up Resistor, One TTL Load
(Open-Drain Output from the DSP)
*TRST is driven low until the EZ-ICE probe is turned on by the emulator at
software start-up. After software start-up,
TRST is driven high.
Figure 6 shows JTAG scan path connections for systems that
contain multiple ADSP-2106x processors.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-TS101SKB2250X | 64-BIT, 125 MHz, OTHER DSP, PBGA484 |
| ADT70GR-REEL7 | ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.51V, 1Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7462ACPZ-500RL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 4Cel, SQUARE, SURFACE MOUNT |
| ADTSM66SV | KEYPAD SWITCH, SPST, MOMENTARY-TACTILE, 0.05A, 12VDC, 3.92 N, SURFACE MOUNT-STRAIGHT |
| ADTS644N/KV | KEYPAD SWITCH, SPST, MOMENTARY-TACTILE, 0.05A, 12VDC, 1.57 N, THROUGH HOLE-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21060LDW-148 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP-21060LKB-160 | 功能描述:IC DSP CONTROLLER 32BIT 225 BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21060LKBZ-160 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADSP-21060LKS-133 | 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 33MHz 33MIPS 240-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:FLOATING PT PROCESSOR, 3.3V, 33MHZ. - Bulk |
| ADSP-21060LKS-160 | 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。