- 您現在的位置：買賣IC網 > PDF目錄385037 > TUSB5052B (Texas Instruments, Inc.) USB to 2-Serial + 1-Parallel Controller With Configurable Optional Hub PDF資料下載
參數資料
| 型號： | TUSB5052B |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | USB to 2-Serial + 1-Parallel Controller With Configurable Optional Hub |
| 中文描述： | USB轉2 -串行接口1 -可配置可選并行控制器集線器 |
| 文件頁數： | 66/84頁 |
| 文件大?。?/td> | 276K |
| 代理商： | TUSB5052B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
8–6
8.3
Mode-2/3: EPP and ECP Modes
These modes of operation support bidirectional data transfer per ECP and EPP protocols. In the output direction,
data/command written to PPDAT/PPADR are placed in the PPDAT register and are transmitted automatically using
ECP/EPP signaling. Typically, the MCU writes to PPADR to set the device address, and data transfer is done by the
DMA to PPDAT register. In the input direction, reverse-channel addressing is not supported. Only data input is
supported. Data input can be accomplished by either MCU or DMA transfer. The following describes the output and
input sequence:
8.3.1
DMA Output Sequence
1.
2.
3.
MCU writes M[2:0] = 010b to PPMCR to set the port to mode-2.
MCU sets PPIMSK[ETxE] = 0 (no TxE interrupt).
MCU writes an address value to the PPADR register. This byte is placed into PD[7:0] and tagged as a
command byte.
MCU sets the proper DMA for output data transfer.
DMA reads a byte from buffer (in SRAM).
DMA writes the byte to the PPDAT register (TxE is used for DMA handshake).
Steps 5 and 6 are repeated without MCU involvement until either the full buffer has been transmitted, or an
error condition has been detected. ( A buffer size of up to 64 bytes can be transferred.)
When the full buffer has been transmitted, the DMA interrupts the MCU.
MCU checks for any error condition.
4.
5.
6.
7.
8.
9.
8.3.2
DMA Input Sequence
1.
2.
3.
4.
5.
6.
MCU writes M[2:0] = 010b to PPMCR to set the port to mode-2.
MCU sets PPIMSK[ERxF] = 0. (no RxF interrupt).
MCU sets the proper DMA for input data transfer.
DMA reads a byte from the PPDAT register (RxF is used for DMA handshake).
DMA writes the byte to buffer (in SRAM).
Steps 4 and 5 are repeated without MCU involvement until either the full buffer has been transmitted, or an
error condition has been detected. ( A buffer size of up to 64 bytes can be transferred)
When the full buffer has been received, the DMA interrupts the MCU.
MCU checks for any error condition.
7.
8.
相關PDF資料 |
PDF描述 |
|---|---|
| TV15C220J | SMD Transient Voltage Suppressor |
| TV30C101J | SMD Transient Voltage Suppressor |
| TV30C580J | SMD Transient Voltage Suppressor |
| TV30C8V0K-G | SMD TRANSLENT VOLTAGE SUPPRESSOR |
| TV30C10V0J-G | SMD TRANSLENT VOLTAGE SUPPRESSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TUSB5052PZ | 功能描述:USB 接口集成電路 5port Hub w/Int Brdg to 2-Serial Ports RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| TUSB5052PZG4 | 功能描述:USB 接口集成電路 5-port Hub with Int Bridge RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| TUSB5152 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:USB to 2-Serial 1-Parallel Controller With Configurable Optional Hub |
| TUSB5152PZ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TUSB522PEVM | 功能描述:EVAL BOARD FOR TUSB522P 制造商:texas instruments 系列:- 零件狀態:在售 主要用途:接口，信號加強器 嵌入式:- 使用的 IC/零件:TUSB522P 主要屬性:2 通道（雙路） 輔助屬性:LED 狀態指示器 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。