參數資料
型號: ST7FLCD1G9M1
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO28
封裝: ROHS COMPLIANT, SO-28
文件頁數: 22/96頁
文件大小: 846K
代理商: ST7FLCD1G9M1
ST7FLCD1
Flash Program Memory
5.5
In-Circuit Programming (ICP)
To perform In-Circuit Programming (ICP), the microcontroller must be switched to ICC (In-Circuit
Communication) mode by an external controller or programming tool.
Depending on the ICP code downloaded in RAM, Flash memory programming can be fully
customized (number of bytes to program, program locations or selection of serial communication
interface for downloading).
When using a STMicroelectronics or third-party programming tool that supports ICP and the
specific microcontroller device, the user only needs to implement the ICP hardware interface on the
application board (see Figure 12). For more details on the pin locations, refer to the device pin
description.
ICP needs between 4 and 6 pins to be connected to the programming tool. Depending on the
desired type of programming, these pins are:
RESET: device reset
VSS: device power supply ground
ICC_CLK: ICC output serial clock pin
ICC_DATA: ICC input serial data pin
VPP: programming voltage
VDD: application board power supply
CAUTION:
1. If the ICC_CLK or ICC_DATA pins are only used as outputs in the application, no signal
isolation is necessary. As soon as the programming tool is plugged to the board, even if an ICC
session is not in progress, the ICC_CLK and ICC_DATA pins are not available for the
application. If they are used as inputs by the application, an isolation such as a serial resistor
has to be implemented in case another device forces the signal. Refer to the Programming
Tool documentation for recommended resistor values.
2. During the ICC session, the programming tool must control the RESET pin. This can lead to
conflicts between the programming tool and the application reset circuit if it drives more than
5 mA at high level (push-pull output or pull-up resistor (< 1 k
)). A Schottky diode can be used
to isolate the application RESET circuit in this case. When using a classical RC network with a
resistor (> 1 k
) or a reset management IC with open-drain output and pull-up resistor
Figure 11: Memory Map and Sector Address
Sector 1
Sector 0
Sector 2
60 KBytes
DV Flash
FFFFh
EFFFh
DFFFh
1000h
Memory Size
52 KBytes
相關PDF資料
PDF描述
ST7FLIT19BF1U6TR 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, QCC20
ST7FLITE09Y0M1 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
ST7FLU05MAE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
ST7LNB0V2Y0M6 8-BIT, 8 MHz, MICROCONTROLLER, PDSO16
ST7LNB1Y0M6 8-BIT, EEPROM, 8 MHz, MICROCONTROLLER, PDSO16
相關代理商/技術參數
參數描述
ST7FLI15BF1U6 功能描述:8位微控制器 -MCU 8-Bit MCU w/ Single Volt Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST7FLI15BF1U6TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST7FLI19BF1M3TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST7FLI19BF1U6TR 功能描述:8位微控制器 -MCU 8-Bit MCU w/ Single Volt Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST7FLI19BY1M3TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT