參數資料
型號： SAA7392
廠商： NXP Semiconductors N.V.
英文描述： Channel encoder/decoder CDR60(通道編碼器/譯碼器)
中文描述： 信道編碼器/解碼器CDR60（通道編碼器/譯碼器）
文件頁數： 69/76頁
文件大?。?/td> 246K
代理商： SAA7392
2000 Mar 21
69
Philips Semiconductors
Preliminary specification
Channel encoder/decoder CDR60
SAA7392
7.
When the correct start address is found on the disc,
the LaserOn and WriteOn2 signals are switched on at
the same time. As a result data flow in the encoder
starts while data is written to the disc.
10.4
Start-up of encoder in synchronous stream
mode
In synchronous stream mode operation is different
because the serial input stream cannot be gated off.
1.
Reset the encoder. Switch LaserOn off, Switch
WriteOn2 off and switch encoder to ‘flush’ mode.
2.
Preset the device.
a) Preset the serial input format
b) Preset the subcode insertion block
c) Preset the EFM modulator block
d) Preset the EFM clock generator. The EFM clock
generator must be programmed to slave to the
incoming serial stream.
3.
Let the disc run at the required speed. Make the motor
servo slave to the W441 wobble clock.
4.
Switch on WriteOn2. This signal must be switched on
to allow data to leave the encoder when it enters it.
(Important to avoid overflow.)
5.
At this stage everything is initialized. The input stream
is running but does not enter the encoder because it is
still in the ‘reset’ state. The output stream is running
too at the same speed as the input speed because the
EFM clock generator is setup like this.
6.
The encoder is switched from ‘flush’ to ‘encode play’
mode. At this point the data stream starts. Data from
the serial in interface enters the encoder while data is
read out from it at approximately the same speed via
the EFM modulator. The FIFO will not overflow. The
data is discarded and not written to the disc because
LaserOn is still switch off.
7.
When the correct start address is found on the disc
LaserOn is switched on allowing data stream to the
disc.
10.5
Operating CDR60 in CAV mode, flow control on
input stream
For very high-speed operation it is possible to lock the
EFM clock to the ATIP wobble carrier. To do this W441
must be selected as the clock source while the position
error is taken from XError. The XError signal gives the time
difference between the ATIPSync and the QSync.
Programming the EFM clock generator like this with a
multiplication factor of 98 will produce an EFM clock that is
synchronous with the ATIP carrier. It can be used to write
data in lock-to-disc mode.
10.6
Operating in CLV Mode, Flow Control on Input
Stream
Simply bypass the EFM PLL and use the system clock as
EFM source.
10.7
Operating in CLV Mode, Synchronous Stream
Operation
When an audio stream is input to the CDR60 encoder the
EFM clock must lock to the serial input WCLK clock signal.
The position error is taken from the FIFOFill signal. This
will produce an EFM clock that is 98 times the WCLK
frequency.
相關PDF資料
PDF描述
SAA7705H Car radio Digital Signal Processor（DSP）(車載電臺數字信號處理器)
SAA7712H Sound effects DSP(聲音效應數字信號處理器)
SAA7712 Sound effects DSP
SAA8110G Digital Signal Processor (DSP) for cameras(應用于照相中的數字信號處理器)
SAA8122A Digital Still Camera Processor (ImagIC family)(數字靜態照相處理器)
相關代理商/技術參數
參數描述
SAA7392HL 制造商:NXP Semiconductors 功能描述:CD-ROM INTERFACE, 80 Pin, Plastic, QFP
SAA7500 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital satellite radio broadcasting tuner decoder SAT-2
SAA7501WP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ARD/ZDF NR.3R1 DIGITAL DECODER|LDCC|68PIN|PLASTIC
SAA-75J2.5-1 制造商:Amphenol Corporation 功能描述:
SAA7704H/204 制造商:NXP Semiconductors 功能描述:Electronic Component
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*