- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C62920D 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC63 PDF資料下載
參數資料
| 型號： | S1C62920D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC63 |
| 封裝： | DIE-63 |
| 文件頁數： | 42/78頁 |
| 文件大?。?/td> | 874K |
| 代理商： | S1C62920D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
S1C62920 TECHNICAL MANUAL
EPSON
39
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
4.9.4 Mask option
Since the input/output terminal of the serial interface is dual used with the I/O ports (P10–P13), the mask
option that selects the specification for the I/O port is also applied to the serial interface.
(1) Output specification
The output specification of the terminals SOUT, SCLK (during the master mode) and SRDY (during the
slave mode) that is used as output in the input/output port of the serial interface is respectively
selected by the mask options of P11, P12 and P13.
Either complementary output or N channel (Nch) open drain as output specification may be selected.
However, even if Nch open drain has been selected, application on the terminal of voltage exceeding
power source voltage is not permitted.
(2) Pull up resistor
Whether or not the SIN (P10) terminal and SCLK (P02) terminal (during slave mode) will use built-in
pull up resistor can be selected.
Normally, the use of pull up resistor should be selected.
(3) FOUT frequency
The FOUT frequency, which is selected by the mask option to select the output port R02 special output
specification, is used for the synchronous clock. When the serial interface is used, the FOUT frequency
must be selected even if the R02 port is not used as the FOUT output.
It can be selected from the four types listed below.
1. OSC1
2. OSC1 /8
3. OSC1 /64
4. OSC3
4.9.5 Control of serial interface
Table 4.9.5.1 list the serial interface control bits and their addresses.
Table 4.9.5.1 Control bits of serial interface
address
Comment
Register
D3
D2
D1
D0
Name
Init
1
0
*1
ESIF
SD0
SD4
EISIF
R/W
ISIF
SCS0
0
SCTRG(W)
SCTRG(R)
ESIF
SD3
SD2
SD1
SD0
SD7
SD6
SD5
SD4
0
EISIF
0
ISIF
0
–
0
–
0
–
0
FOUT
Trigger
Run
SIF port
Enable
Yes
Slave
–
Stop
I/O port
Mask
No
SCTRG
SD1
SD5
0
R
SD2
SD6
0
R
0
SCS0
R/W
SD3
SD7
0
E8H
E9H
EAH
F0H
F8H
*2
*5
*4
*7
Serial I/F clock mode selection
Unused
Serial I/F clock trigger (writing)
Serial I/F clock status (reading)
P1 port function selection
MSB
Serial I/F data (low-order 4 bits)
LSB
MSB
Serial I/F data (high-order 4 bits)
LSB
Unused
Interrupt mask register (Serial I/F)
Unused
Interrupt factor flag (Serial I/F)
R/W
R
*1 Initial value at the time of initial reset
*5 Constantly "0" when being read
*2 Not set in the circuit
*6 Refer to main manual
*3 Undefined
*7 Page switching in I/O memory is not necessary
*4 Reset (0) immediately after being read
相關PDF資料 |
PDF描述 |
|---|---|
| S1C62A33D | 4-BIT, MROM, 0.6 MHz, MICROCONTROLLER, UUC86 |
| S1C62N82F | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, PQFP80 |
| S1C63158F0A0100 | 4-BIT, FLASH, 4.2 MHz, MICROCONTROLLER, PQFP100 |
| S1C63358F0A0100 | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP100 |
| S1C63406F | 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63004 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63008 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63016 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63158 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。