參數資料
型號: PSD833F2-15M
元件分類: 微控制器/微處理器
英文描述: 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52
封裝: PLASTIC, QFP-52
文件頁數: 52/122頁
文件大小: 489K
代理商: PSD833F2-15M
Preliminary Information
PSD8XXF Family
31
The
PSD8XXF
Functional
Blocks
(cont.)
9.2 PLDs
The PLDs bring programmable logic functionality to the PSD8XXF. After specifying the
logic for the PLDs using the PSDabel tool in PSDsoft, the logic is programmed into the
device and available upon power-up.
The PSD8XXF contains two PLDs: the Decode PLD (DPLD), and the Complex PLD
(CPLD). The PLDs are briefly discussed in the next few paragraphs, and in more detail in
sections 9.2.1 and 9.2.2. Figure 10 shows the configuration of the PLDs.
The DPLD performs address decoding for internal components, such as memory,
registers, and I/O port selects.
The CPLD can be used for logic functions, such as loadable counters and shift registers,
state machines, and encoding and decoding logic. These logic functions can be
constructed using the 16 Output Micro
Cells (OMCs), 24 Input MicroCells (IMCs), and
the AND array. The CPLD can also be used to generate external chip selects.
The AND array is used to form product terms. These product terms are specified using
PSDabel. An Input Bus consisting of 73 signals is connected to the PLDs. The signals are
shown in Table 15.
Input Source
Input Name
Number
of Signals
MCU Address Bus
A[15:0]
*
16
MCU Control Signals
CNTL[2:0]
3
Reset
RST
1
Power Down
PDN
1
Port A Input Micro
Cells
PA[7-0]
8
Port B Input Micro
Cells
PB[7-0]
8
Port C Input Micro
Cells
PC[7-0]
8
Port D Inputs
PD[2:0]
3
Page Register
PGR(7:0)
8
Micro
Cell AB Feedback
MCELLAB.FB[7:0]
8
Micro
Cell BC Feedback
MCELLBC.FB[7:0]
8
Boot Flash Programming Status Bit
Rdy/Bsy
1
Table 15. DPLD and CPLD Inputs
NOTE: The address inputs are A[19:4] in 80C51XA mode.
The Turbo Bit
The PLDs in the PSD8XXF can minimize power consumption by switching off when inputs
remain unchanged for an extended time of about 70 ns. Setting the Turbo mode bit to off
(Bit 3 of the PMMR0 register) automatically places the PLDs into standby if no inputs
are changing. Turbo-off mode increases propagation delays while reducing power
consumption. Refer to the Power Management Unit section on how to set the Turbo Bit.
Additionally, five bits are available in the PMMR2 register to block MCU control signals
from entering the PLDs. This reduces power consumption and can be used only when
these MCU control signals are not used in PLD logic equations.
相關PDF資料
PDF描述
PSD835G2V-B-90MI Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD835G2V-B-90U Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD835G2V-B-90UI Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD835G2V-C-12B81I Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD835G2V-C-12M Configurable Memory System on a Chip for 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
PSD833F2-90J 功能描述:CPLD - 復雜可編程邏輯器件 5.0V 1M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD833F2-90JI 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 1M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD833F2-90M 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 1M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD833F2-90MI 功能描述:CPLD - 復雜可編程邏輯器件 5.0V 1M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD834F2-15M 制造商:STMicroelectronics 功能描述:Flash In-System Programmable Peripherals 52-Pin PQFP