參數資料
型號: GS4910BCNE3
廠商: Gennum Corporation
英文描述: HD/SD/Graphics Clock and Timing Generator with GENLOCK
中文描述: 高清/標清/圖形時鐘和定時發生器鎖相
文件頁數: 58/113頁
文件大小: 1017K
代理商: GS4910BCNE3
GS4911B/GS4910B Data Sheet
36655 - 2
April 2006
58 of 113
3.6.3 Adjustable Locking Time
The GS4911B/GS4910B offers two different locking mechanisms to allow the user
to control the PLL lock time and the integrity of the output signal during the locking
process. The locking process is said to take place after the application of the input
reference and before the LOCK_LOST signal is set LOW.
By default, the internal PLL will crash lock. This locking process will ensure a
minimum PLL locking time; however, crash lock will cause the phase of the output
clock and timing signals to jump during the locking process. The crash behaviour
of the video PLL is controlled by the Crash_Time bits of register address 24h.
Alternatively, the user may set bit 1 of register 16h HIGH to force the PLL to drift
lock. Drift lock will increase the locking time of the PLL, but will maintain the signal
integrity of the output clock and timing pulses during the locking process.
As discussed in
Section 3.5.3 on page 47
, the device will normally drift lock when
the reference is removed and subsequently re-applied during Genlock mode.
3.6.4 Adjustable Loop Bandwidth
The default loop bandwidth of the GS4911B/GS4910B's internal video PLL is 10Hz
when the output video standard is the same as the input reference format. For
other cross-locking combinations, the default loop bandwidth may be smaller than
1Hz or as large as 30Hz.
The user may adjust the loop bandwidth of both the video and audio PLLs to a
value that depends on the input, output, and audio standards selected, as well as
on the amplitude of the jitter present on the applied HSYNC signal. Increasing the
loop bandwidth will result in a shorter PLL lock time, but will allow more frequency
components of jitter to be passed to the outputs. Decreasing the loop bandwidth
will decrease the output jitter, but will result in a longer PLL lock time.
3.6.4.1 Loop Bandwidth of the Video PLL
The capacitive component of the filter controlling the video loop bandwidth is
determined by the Video_Cap_Genlock register and the resistive component is
determined by the Video_Res_Genlock register. These two registers are located
at addresses 26h and 27h, respectively, of the host interface.
To determine the setting of Video_Res_Genlock and Video_Cap_Genlock, the
following equations must be solved:
Video_Res_Genlock
47
log
2
6
BW
JITTERIN
H_Feedback_Divide
×
×
×
(
)
+
=
Video_Cap_Genlock
Video_Res_Genlock
21
相關PDF資料
PDF描述
GS4911B HD/SD/Graphics Clock and Timing Generator with GENLOCK
GS4911BCNE3 HD/SD/Graphics Clock and Timing Generator with GENLOCK
GS4915 CONN,S/R,8 POS,254C-08-1, CLOSED END STRAIN RELIEF COVER
GS6332 3 Pin, Low-Power, P Reset Circuits
GS6332UR15D1 3 Pin, Low-Power, P Reset Circuits
相關代理商/技術參數
參數描述
GS4911ACNE3 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述:
GS4911B 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD/SD/Graphics Clock and Timing Generator with GENLOCK
GS4911B_09 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD/SD/Graphics Clock and Timing Generator with GENLOCK
GS4911BCNE3 功能描述:IC RE-TIMER RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
GS4915 制造商:GENNUM 制造商全稱:GENNUM 功能描述:ClockCleaner