
Philips Semiconductors
Pin List
PRODUCT SPECIFICATION
1-7
Audio Out (always acts as sender, but can be master or slave for D/A timing)
AO_OSCLK
B14
STRG3
OUT
Over sampling clock. This output can be programmed to emit any frequency up to 40
MHz, with a sub-Hertz resolution. It is intended for use as the 256 or 384fs over sam-
pling clock by the external D/A conversion subsystem. A board level 27-33 ohm series
resistor is recommended to reduce ringing.
AO_SCK
A14
STRG5
I/O
When the Audio Out (AO) unit is programmed to act as the serial interface timing
slave (power up default), AO_SCK acts as input. It receives the Serial Clock from
the external audio D/A subsystem. The clock is treated as fully asynchronous to the
TM1300 main clock.
When the AO unit is programmed to act as serial interface timing master, AO_SCK
acts as output. It drives the serial clock for the external audio D/A subsystem. The
clock frequency is a programmable integral divisor of the AO_OSCLK frequency.
AO_SCK is limited to 22 MHz. The sample rate of valid samples embedded within the
serial stream is variable. If used as output, a board level 27-33 ohm series resistor is
recommended to reduce ringing.
AO_SD1
B13
WEAK5
OUT
Serial data to external stereo audio D/A subsystem for rst 2 of 8 channels. The timing
of transitions on this output is determined by the CLOCK_EDGE bit in the AO_SERIAL
register, and can be on positive or negative AO_SCK edges.
AO_SD2
A13
WEAK5
OUT
Serial data.
AO_SD3
C12
WEAK5
OUT
Serial data.
AO_SD4
B12
WEAK5
OUT
Serial data.
AO_WS
A15
WEAK5
I/O
When the AO unit is programmed as the serial-interface timing slave (power-up
default), AO_WS acts as an input. AO_WS is sampled on the opposite AO_SCK
edge at which AO_SDx are asserted.
When the AO unit is programmed as serial-interface timing master, AO_WS acts as
an output. AO_WS is asserted on the same AO_SCK edge as AO_SDx.
AO_WS is the word-select or frame-synchronization signal from/to the external D/A
subsystem. Each audio channel receives 1 sample for every WS period.
S/PDIF Output (Output)
SPDO
A12
STRG3
OUT
Self clocking serial data stream as per IEC958, with 1937 extensions. Note that the
low impedance output buffer requires a 27 to 33 ohm series terminator close to
TM1300 in order to match the board trace impedance. This series terminator can be/
must be part of the voltage divider needed to create the coaxial output through the AC
isolation transformer.
Synchronous Serial Interface (SSI) to an off-chip modem front-end
SSI_CLK
B11
WEAK5
IN
Clock signal of the synchronous serial interface to an off-chip modem analog frontend
or ISDN terminal adapter; provided by the receive channel of an external communica-
tion device.
SSI_RXFSX
A11
WEAK5
IN
Receive frame sync reference of the synchronous serial interface, provided by the
receive channel of an external communication device.
SSI_RXDATA
A10
WEAK5
IN
Receive serial data input; provided by the receive channel of an external communica-
tion device.
SSI_TXDATA
B10
WEAK5
OUT
Transmit serial data output; sent to the transmit channel of the external communication
device.
SSI_IO1
A9
WEAK5
I/O
General purpose programmable I/O. Set to input on power up.
SSI_IO2
B9
WEAK5
I/O
General purpose programmable I/O. Set to input on power up. Can also be pro-
grammed to function as the transmit channel frame synchronization reference output.
Pin Name
BGA
Ball
Pad
Type
Mode
Description