參數資料
型號： PSD913F1V
英文描述： 130V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a SMD-2 package; A IRHNA57163SE with Standard Packaging
中文描述： Flash在系統可編程微控制器外設
文件頁數： 74/94頁
文件大小： 463K
代理商： PSD913F1V
Preliminary
PSD913F1
73
-90
-12
-15
Symbol
Parameter
Conditions Min Max
Min
Max
Min
Max
Unit
t
ISCCF
t
ISCCH
t
ISCCL
t
ISCCF-P
t
ISCCH-P
t
ISCCL-P
t
ISCPSU
t
ISCPH
t
ISCPCO
TCK Clock Frequency (except for PLD)
TCK Clock High Time
TCK Clock Low Time
TCK Clock Frequency (for PLD only)
TCK Clock High Time (for PLD only)
TCK Clock Low Time (for PLD only)
ISC Port Set Up Time
ISC Port Hold Up Time
ISC Port Clock to Output
ISC Port High-Impedance to
Valid Output
ISC Port Valid Output to High-Impedance
(Note 1)
(Note 1)
(Note 1)
(Note 2)
(Note 2)
(Note 2)
18
16
14
MHz
ns
ns
MHz
ns
ns
ns
ns
ns
26
26
29
29
31
31
2
2
2
240
240
8
5
240
240
10
5
240
240
10
5
23
24
25
t
ISCPZV
23
24
25
ns
t
ISCPVZ
23
24
25
ns
ISC Timing
(5 V ± 10%)
Microcontroller Interface – PSD913F1 AC/DC Parameters
(5V ±10% Versions)
Symbol
Parameter
Min
Typ
Max
Unit
Flash Bulk Erase (Preprogrammed) (Note 1)
3
30
sec
Flash Bulk Erase (Not Preprogrammed)
5
sec
t
WHQV3
t
WHQV2
t
WHQV1
Sector Erase (Preprogrammed)
1
30
sec
Sector Erase (Not Preprogrammed)
2.2
sec
Byte Program
14
1200
μs
Program/Erase Cycles (Per Sector)
100,000
cycles
t
WHWLO
Sector Erase Time-Out
100
μs
t
Q7VQV
DQ7 Valid to Output (DQ7-0) Valid
(Data Polling) (Note 2)
30
ns
Flash Program, Write and Erase Times
(5 V ± 10%)
NOTES:
1. Programmed to all zeros before erase.
2. The Polling Status DQ7 is valid t
Q7VQV
ns, before the data byte DQ0-7 is valid for reading.
Symbol
Parameter
Min
Typ
Max
Unit
t
EEHWL
t
BLC
t
WCB
t
WCP
Write Protect After Power Up
5
msec
EEPROM Byte Load Cycle Timing (Note 1)
0.2
120
μsec
EEPROM Byte Write Cycle Time
4
10
msec
EEPROM Page Write Cycle Time (Note 2)
6
30
msec
Program/Erase Cycles (Per Sector)
10,000
cycles
EEPROM Write Times
(5 V ± 10%)
NOTES:
1. If the maximum time has elapsed between successive writes to an EEPROM page, the transfer of this data to EEPROM cells will
begin. Also, bytes cannot be written (loaded) to a page any faster than the indicated minimum type.
2. These specifications are for writing a page to EEPROM cells.
NOTES:
1. For “non-PLD” programming, erase or in ISC by-pass mode.
2. For program or erase PLD only.
相關PDF資料
PDF描述
PSD913F2 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA7260 with optional Total Dose Rating of 300kRads
PSD913F2V 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA7260 with Standard Packaging
PSD913F2(中文) Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD934F2(中文) Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
PSD913F2 Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
相關代理商/技術參數
參數描述
PSD913F1V-12B81 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F1V-12B81I 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F1V-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F1V-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913F1V-12M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*