- 您現在的位置：買賣IC網 > PDF目錄367908 > pentium III (Intel Corp.) pentium III Processor for the PGA370 Socket at 500MHz to 933MHz(工作頻率500到933兆赫茲活動帶PGA370插孔奔III處理器) PDF資料下載
參數資料
| 型號： | pentium III |
| 廠商： | Intel Corp. |
| 英文描述： | pentium III Processor for the PGA370 Socket at 500MHz to 933MHz(工作頻率500到933兆赫茲活動帶PGA370插孔奔III處理器) |
| 中文描述： | 奔騰III處理器在500MHz到933MHz的（工作頻率500到933兆赫茲活動帶PGA370插孔奔三處理器的PGA370插座） |
| 文件頁數： | 40/78頁 |
| 文件大小： | 610K |
| 代理商： | PENTIUM III |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
40
Datasheet
Pentium
III Processor for the PGA370 Socket at 500 MHz to 933 MHz
that just meets the pulse duration for a specific magnitude where the AF < 1, means that there can
be NO other overshoot/undershoot events, even of lesser magnitude (note that if AF = 1, then the
event occurs at all times and no other events can occur).
Note:
Activity factor for AGTL+ signals is referenced to BCLK frequency.
Note:
Activity factor for CMOS signals is referenced to PICCLK frequency.
3.3.5
Reading Overshoot/Undershoot Specification Tables
The overshoot/undershoot specification for the Pentium
III
processor for the PGA370 socket is not
a simple single value. Instead, many factors are needed to determine what the over/undershoot
specification is. In addition to the magnitude of the overshoot, the following parameters must also
be known: the junction temperature the processor will be operating at, the width of the overshoot
(as measured above 1.635V) and the Activity Factor (AF). To determine the allowed overshoot for
a particular overshoot event, the following must be done:
1. Determine the signal group that particular signal falls into. If the signal is an AGTL+ signal
operating with a 100 MHz system bus, use
Table 20
(100MHz AGTL+ signal group). If the
signal is an AGTL+ signal operating with a 133MHz system bus, use
Table 21
(133 MHz
AGTL+ signal group). If the signal is a CMOS signal, use
Table 22
(33 MHz CMOS signal
group).
2. Determine the maximum junction temperature (Tj) for the range of processors that the system
will support (80
o
C or 85
o
C).
3. Determine the Magnitude of the overshoot (relative to V
SS
)
4. Determine the Activity Factor (how often does this overshoot occur)
5. From the appropriate Specification table, read off the Maximum Pulse Duration (in ns)
allowed.
6. Compare the specified Maximum Pulse Duration to the signal being measured. If the Pulse
Duration measured is less than the Pulse Duration shown in the table, then the signal meets the
specifications.
The above procedure is similar for undershoots after the undershoot waveform has been converted
to look like an overshoot. Undershoot events must be analyzed separately from Overshoot events
as they are mutually exclusive.
Below is an example showing how the maximum pulse duration is determined for a given
waveform.
NOTES:
1. Corresponding Maximum Puse Duration Specification - 2.4 ns
2. Pulse Duration (measured) - 2.0 ns
Given the above parameters, and using
Table 21
(85
o
C/AF = 0.1 column) the maximum allowed
pulse duration is 2.4 ns. Since the measure pulse duration is 2.0 ns, this particular overshoot event
passes the overshoot specifications, although this doesn't guarantee that the combined overshoot/
undershoot events meet the specifications.
Table 19. Example Platform Information
Required Information
Maximum Platform Support
Notes
FSB Signal Group
133 MHz AGTL+
Max Tj
85 °C
Overshoot Magnitude
2.13V
Measured Value
Activity Factor (AF)
0.1
Measured overshoot occurs on
average every 20 clocks
相關PDF資料 |
PDF描述 |
|---|---|
| pentium II | pentium II processor With On-die Cache Mobile Module Connector 1 (MMC-1)(帶緩存和連接器1的奔II處理器) |
| PERICOMPI7C8150 | 2-Port PCI-to-PCI Bridge |
| PESDXL2BT | Low capacitance double bidirectional ESD protection diodes in SOT23 |
| PESDXL2UM | LJT 23C 21#20 2#16 PIN RECP |
| PETAM1270BK300R | BRAID SLEEVING 300M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P-ENV568K3G3 | 制造商:Panasonic Industrial Company 功能描述:TUNER |
| PEO14012 | 制造商:TE Connectivity 功能描述:RELAY SPCO 12VDC |
| PEO14024 | 制造商:TE Connectivity 功能描述:RELAY SPCO 24VDC |
| PEO96742 | 制造商:Delphi Corporation 功能描述:ASM TERM |
| PEOODO3A | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint |
發布緊急采購，3分鐘左右您將得到回復。