- 您現在的位置：買賣IC網 > PDF目錄367908 > pentium III (Intel Corp.) pentium III Processor for the PGA370 Socket at 500MHz to 933MHz(工作頻率500到933兆赫茲活動帶PGA370插孔奔III處理器) PDF資料下載
參數資料
| 型號： | pentium III |
| 廠商： | Intel Corp. |
| 英文描述： | pentium III Processor for the PGA370 Socket at 500MHz to 933MHz(工作頻率500到933兆赫茲活動帶PGA370插孔奔III處理器) |
| 中文描述： | 奔騰III處理器在500MHz到933MHz的（工作頻率500到933兆赫茲活動帶PGA370插孔奔三處理器的PGA370插座） |
| 文件頁數： | 14/78頁 |
| 文件大小： | 610K |
| 代理商： | PENTIUM III |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
14
Datasheet
Pentium
III Processor for the PGA370 Socket at 500 MHz to 933 MHz
2.2.4
HALT/Grant Snoop State—State 4
The processor responds to snoop transactions on the system bus while in Stop-Grant state or in
AutoHALT Power Down state. During a snoop transaction, the processor enters the HALT/Grant
Snoop state. The processor stays in this state until the snoop on the system bus has been serviced
(whether by the processor or another agent on the system bus). After the snoop is serviced, the
processor returns to the Stop-Grant state or AutoHALT Power Down state, as appropriate.
2.2.5
Sleep State—State 5
The Sleep state is a very low power state in which the processor maintains its context, maintains
the phase-locked loop (PLL), and has stopped all internal clocks. The Sleep state can only be
entered from the Stop-Grant state. Once in the Stop-Grant state, the SLP# pin can be asserted,
causing the processor to enter the Sleep state. The SLP# pin is not recognized in the Normal or
AutoHALT states.
Snoop events that occur while in Sleep State or during a transition into or out of Sleep state will
cause unpredictable behavior.
In the Sleep state, the processor is incapable of responding to snoop transactions or latching
interrupt signals. No transitions or assertions of signals (with the exception of SLP# or RESET#)
are allowed on the system bus while the processor is in Sleep state. Any transition on an input
signal before the processor has returned to Stop-Grant state will result in unpredictable behavior.
If RESET# is driven active while the processor is in the Sleep state, and held active as specified in
the RESET# pin specification, then the processor will reset itself, ignoring the transition through
Stop-Grant State. If RESET# is driven active while the processor is in the Sleep State, the SLP#
and STPCLK# signals should be deasserted immediately after RESET# is asserted to ensure the
processor correctly executes the reset sequence.
While in the Sleep state, the processor is capable of entering its lowest power state, the Deep Sleep
state, by stopping the BCLK input (see
Section 2.2.6
). Once in the Sleep or Deep Sleep states, the
SLP# pin can be deasserted if another asynchronous system bus event occurs. The SLP# pin has a
minimum assertion of one BCLK period.
2.2.6
Deep Sleep State—State 6
The Deep Sleep state is the lowest power state the processor can enter while maintaining context.
The Deep Sleep state is entered by stopping the BCLK input (after the Sleep state was entered from
the assertion of the SLP# pin). The processor is in Deep Sleep state immediately after BLCK is
stopped. It is recommended that the BLCK input be held low during the Deep Sleep State.
Stopping of the BCLK input lowers the overall current consumption to leakage levels.
To re-enter the Sleep state, the BLCK input must be restarted. A period of 1 ms (to allow for PLL
stabilization) must occur before the processor can be considered to be in the Sleep state. Once in
the Sleep state, the SLP# pin can be deasserted to re-enter the Stop-Grant state.
While in Deep Sleep state, the processor is incapable of responding to snoop transactions or
latching interrupt signals. No transitions or assertions of signals are allowed on the system bus
while the processor is in Deep Sleep state. Any transition on an input signal before the processor
has returned to Stop-Grant state will result in unpredictable behavior.
相關PDF資料 |
PDF描述 |
|---|---|
| pentium II | pentium II processor With On-die Cache Mobile Module Connector 1 (MMC-1)(帶緩存和連接器1的奔II處理器) |
| PERICOMPI7C8150 | 2-Port PCI-to-PCI Bridge |
| PESDXL2BT | Low capacitance double bidirectional ESD protection diodes in SOT23 |
| PESDXL2UM | LJT 23C 21#20 2#16 PIN RECP |
| PETAM1270BK300R | BRAID SLEEVING 300M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P-ENV568K3G3 | 制造商:Panasonic Industrial Company 功能描述:TUNER |
| PEO14012 | 制造商:TE Connectivity 功能描述:RELAY SPCO 12VDC |
| PEO14024 | 制造商:TE Connectivity 功能描述:RELAY SPCO 24VDC |
| PEO96742 | 制造商:Delphi Corporation 功能描述:ASM TERM |
| PEOODO3A | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint |
發布緊急采購，3分鐘左右您將得到回復。