- 您現在的位置：買賣IC網 > PDF目錄382377 > PCA5007 (NXP Semiconductors N.V.) Pager baseband controller PDF資料下載
參數資料
| 型號： | PCA5007 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Pager baseband controller |
| 中文描述： | 傳呼機基帶控制器 |
| 文件頁數： | 61/112頁 |
| 文件大?。?/td> | 604K |
| 代理商： | PCA5007 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
1998 Oct 07
61
Philips Semiconductors
Product specification
Pager baseband controller
PCA5007
Fig.33 Efficiency in standby mode as a function of load current.
(1) V
BAT
= 1.5 V.
(2) V
BAT
= 1.2 V.
(3) V
BAT
= 0.9 V.
handbook, halfpage
(%)
0
1
2
4
0
IL (mA)
80
MGR136
3
60
40
20
(2)
(3)
(1)
6.22.3
S
TART
-
UP DESCRIPTION
6.22.3.1
Start-up from reset
An external RC network together with an on-chip Schmitt
trigger is used to generate a reset pulse after the insertion
of a new battery (see Section 6.21). A reset pulse at the
RESETIN pin resets the SFRs and the internal registers of
the DC/DC converter to the factory programmed values
and the start-up sequence shown in Fig.34 is started.
The reset pulse must be essentially longer then the rise
time of V
BAT
.
The start-up sequence is divided into several steps:
1.
Start-up 76.8 kHz crystal oscillator (256 clocks).
2.
Boost up of V
DD
to approximately 1.7 V using the
76.8 kHz clock. During this phase, the p-channel
MOSFET is switched off and the charge is transferred
via the external Schottky diode.
3.
Start of the 6 MHz clock
;
(see Section 6.12).
2
76.8 kHz
---------1
×
4.
Boost up V
DD
to 2.2 V using the internal 6 MHz clock
and the p-channel MOSFET. As soon as
V
DD
≥
2.15 V, the stable flag is set to indicate that the
system is powered-up successfully and the
microcontroller starts operating. The DC/DC converter
now stays in the normal mode of the normal operating
mode.
If a reset pulse is generated during normal operation, the
DC/DC converter immediately resets the whole system
and enters the start-up sequence.
6.22.3.2
Start-up from off mode
Start-up from off mode behaves exactly as start-up from
external reset (see Fig.34) except that:
The internal registers of the DC/DC converter are not
reset; however the DC/DC converter SFRs are reset.
off mode is exited when one of the following events occur:
Key pressed
Minute interrupt
Wake-up interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA5007H | Pager baseband controller |
| PCA5010 | Pager baseband controller |
| PCA5010H | Pager baseband controller |
| PCA82C200 | STAND-ALONE CAN-CONTROLLER |
| PCA82C200P | STAND-ALONE CAN-CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA5007H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5007H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| PCA5010 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。