參數資料
型號： PCA5007
廠商： NXP Semiconductors N.V.
英文描述： Pager baseband controller
中文描述： 傳呼機基帶控制器
文件頁數： 23/112頁
文件大?。?/td> 604K
代理商： PCA5007
1998 Oct 07
23
Philips Semiconductors
Product specification
Pager baseband controller
PCA5007
6.9
Serial interface SIO0: UART
The UART interface of the PCA5007 implements a subset
of the complete standard as defined in e.g. the P80CL580.
6.9.1
D
IFFERENCES TO THE STANDARD
80C51 UART
The following deviations from the standard exist:
If [SM1 and SM0] = 10 then Mode 1 (8-bit data
transmission) is selected, with a fixed baud rate
(4800/9600 bits/s)
If [SM1 and SM0] = 01 then Mode 2 (9-bit data
transmission) is selected, with a fixed baud rate
(4800/9600 bits/s)
Modes 0 and 3 and the variable baud rate selection
using Timer 1 overflow is not available
The SM2 bit has no function
The time reference for Modes 1 and 2 is taken from the
76.8 kHz oscillator, instead of the original
6.9.2
UART
MODES
This serial port is full duplex which means that it can
transmit and receive simultaneously. It is also
receive-buffered and can commence reception of a
second byte before a previously received byte has been
read from the register. However, if the first byte has not
been read by the time the reception of the second byte is
complete, the second byte will be lost. The serial port
receive and transmit registers are both accessed via the
special function register S0BUF. Writing to S0BUF loads
the transmit register and reading from S0BUF accesses a
physically separate receive register.
f
12
-----------
The serial port can operate in 2 modes:
Mode 1 10 bits are transmitted (through TXD) or received
(through RXD): a START bit (0), 8 data bits (LSB
first) and a STOP bit (1). On receive, the stop bit
goes into RB8 in special function register S0CON
(see Figs 9 and 10).
Mode 2 11 bits are transmitted (through TXD) or received
(through RXD): a START bit (0), 8 data bits (LSB
first), a programmable 9th data bit and a STOP
bit (1). On transmit, the 9th data bit (TB8 in
S0CON) can be assigned the value of 0 or 1.
Or, for example, the parity bit (P, in the PSW)
could be moved into TB8. On receive, the
9th data bit goes into RB8 in S0CON, while the
STOP bit is ignored (see Figs 9 and 11).
In both modes the baud rate can be selected to either
4800 or 9600 depending on the SMOD bit in the PCON
SFR. If SMOD = 0 the baud rate is 4800, if SMOD = 1 the
baud rate is 9600 with a 76.8 kHz quartz crystal.
In both modes, transmission is initiated by any instruction
that uses S0BUF as a destination register. Reception is
initiated by the incoming start bit if REN = 1.
6.9.3
S
ERIAL
P
ORT
C
ONTROL
R
EGISTER
(S0CON)
The serial port control and status register is the special
function register S0CON (see Table 16). The register
contains not only the mode selection bits, but also the
9th data bit for transmit and receive (TB8 and RB8), and
the serial port interrupt bits (TI and RI).
Table 16
Serial Port Control Register (S0CON, SFR address 98H)
7
6
5
4
3
2
1
0
SM0
SM1
REN
TB8
RB8
TI
RI
相關PDF資料
PDF描述
PCA5007H Pager baseband controller
PCA5010 Pager baseband controller
PCA5010H Pager baseband controller
PCA82C200 STAND-ALONE CAN-CONTROLLER
PCA82C200P STAND-ALONE CAN-CONTROLLER
相關代理商/技術參數
參數描述
PCA5007H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5007H/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
PCA5010 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5010H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5010H/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*