參數資料
型號： PCA5007
廠商： NXP Semiconductors N.V.
英文描述： Pager baseband controller
中文描述： 傳呼機基帶控制器
文件頁數： 57/112頁
文件大小： 604K
代理商： PCA5007
1998 Oct 07
57
Philips Semiconductors
Product specification
Pager baseband controller
PCA5007
6.21
Reset
To initialize the PCA5007 a reset is performed by using
either of the 2 following methods:
Applying an external reset signal to the RESETIN pin
Via the on-chip watchdog timer.
The reset state of the output pins is given in separate
tables (Tables 2 to 6). The reset state of the SFRs is given
in a separate overview (see Table 1).
While a reset is applied to the device the output RESOUT
is driven LOW.
The internal RAM is not affected by reset. When V
DD
is
turned on, the RAM contents are indeterminate.
6.21.1
E
XTERNAL RESET USING THE
RESETIN
PIN
The external reset input for the PCA5007 is the RESETIN
pin. A Schmitt trigger is used at the input for noise
rejection. Immediately after pin RESETIN goes HIGH, an
internal reset is executed. As a consequence the SFRs
and port pins adopt their reset state, ALE and PSEN are
held HIGH. As long as the RESETIN pin stays HIGH, the
reset state is maintained. When RESETIN goes LOW, the
device start-up sequence is executed (see Section 6.22).
6.21.2
E
XTERNAL POWER
-
ON RESET USING THE
RESETIN
PIN
An automatic reset can be obtained by connecting the
RESETIN pin to V
BAT
via a capacitor and to V
SS
via a
resistor. At power-on, the voltage on the RESETIN pin is
equal to V
BAT
and decreases from V
BAT
as the capacitor
charges through the resistor to V
SS
. V
RESETIN
must remain
higher than the threshold of the Schmitt trigger for a
duration of t
RESETIN
(see Chapter “AC characteristics”).
The reset configuration is shown in Fig.28.
6.21.3
I
NTERNAL RESET
The watchdog which is available in the PCA5007
(see Section 6.16) will force a reset if it is enabled and
expires.
A reset is also forced, when the DC/DC converter restarts
operation from the off mode (see Section 6.22.3).
All resets to the microcontroller can be observed as
negative pulses at the output RESOUT.
Fig.28 Application diagram for external power-on reset configuration.
handbook, full pagewidth
MGR131
VBAT
VBAT
VSS
RESETIN
RESET AND
POWER
CONTROLLER
internal reset
for microcontroller
RESOUT
PCA5007
watchdog
restart DC/DC
converter
10
μ
F
10 k
相關PDF資料
PDF描述
PCA5007H Pager baseband controller
PCA5010 Pager baseband controller
PCA5010H Pager baseband controller
PCA82C200 STAND-ALONE CAN-CONTROLLER
PCA82C200P STAND-ALONE CAN-CONTROLLER
相關代理商/技術參數
參數描述
PCA5007H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5007H/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
PCA5010 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5010H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5010H/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*