參數資料
型號： PCA5007
廠商： NXP Semiconductors N.V.
英文描述： Pager baseband controller
中文描述： 傳呼機基帶控制器
文件頁數： 32/112頁
文件大?。?/td> 604K
代理商： PCA5007
1998 Oct 07
32
Philips Semiconductors
Product specification
Pager baseband controller
PCA5007
Fig.16 Synchronization of local counter operation and access from the microcontroller.
handbook, full pagewidth
MGR119
76.8 kHz
SET flag (local)
store (local)
data (SFR)
data (local)
counter
reload from
local data
I
I
1
I
2
I
3
I
4
1
0
K
K
1
K
2
K
K
6.12
6 MHz oscillator
6.12.1
F
UNCTION
The 6 MHz oscillator provides the clock for the DC/DC
converter, the I
2
C-bus interface, the port I/Os and for the
external memory access timing (ALE/PSEN).
The 6 MHz oscillator is a 5 inverter stage current
controlled ring oscillator. The oscillator is optimized for low
operating current consumption.
The actual frequency of the oscillator can be measured by
activating the MFR signal. An 8-bit counter will then be
reset and will start counting at the first rising edge of the
76.8 kHz signal and will stop counting at the next rising
edge of the 76.8 kHz signal. The processor then can read
the contents of the MFR counter.
The processor can adjust the oscillator frequency using
the F0 to F4 signals (control of source current for ring
oscillator).
The 6 MHz oscillator is enabled by hardware only during
the start-up phase and whenever the DC/DC converter
needs the 6 MHz clock. In all other cases the 6 MHz
oscillator is switched off by hardware.
The DC/DC converter does not need the 6 MHz clock
when set in the standby mode.
If the 6 MHz output is required as a frequency source for
other blocks (e.g. I
2
C-bus) the software needs to enable it
explicitly by setting ENB = 1. Besides the DC/DC
converter the following functions require the operation of
the 6 MHz oscillator:
I
2
C-bus block as basic time reference
Port output logic. Software commands that write to the
ports need this clock to complete the operation (if a
program ‘hangs’, this could be the problem).
Code fetching from external memories needs the clock
for the ALE/PSEN timing (e.g. LJMP 5000H needs this
clock for completion).
When the ENB bit has been set by software, the clock will
be available internally after the start-up time of this
oscillator. The start-up time is 2 to 3 periods of the
76.8 kHz reference frequency.
相關PDF資料
PDF描述
PCA5007H Pager baseband controller
PCA5010 Pager baseband controller
PCA5010H Pager baseband controller
PCA82C200 STAND-ALONE CAN-CONTROLLER
PCA82C200P STAND-ALONE CAN-CONTROLLER
相關代理商/技術參數
參數描述
PCA5007H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5007H/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
PCA5010 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5010H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller
PCA5010H/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*