- 您現在的位置：買賣IC網 > PDF目錄12023 > P89V664FBC,557 (NXP Semiconductors)IC 80C51 MCU FLASH 64K 44-TQFP PDF資料下載
參數資料
| 型號： | P89V664FBC,557 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 46/90頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU FLASH 64K 44-TQFP |
| 產品培訓模塊： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 標準包裝： | 800 |
| 系列： | 89V |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 40MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 36 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-TQFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1001-ND - USB IN-CIRCUIT PROG 80C51ISP |
| 其它名稱： | 568-2437 935280835557 P89V664FBC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
P89V660_662_664
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3.1 — 17 October 2011
50 of 90
NXP Semiconductors
P89V660/662/664
80C51 with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
6.7.5 Framing error
Framing error (FE) is reported in the SCON.7 bit if SMOD0 (PCON.6) = 1. If SMOD0 = 0,
SCON.7 is the SM0 bit for the UART, it is recommended that SM0 is set up before
SMOD0 is set to ‘1’.
6.7.6 More about UART mode 1
Reception is initiated by a detected 1-to-0 transition at RXD. For this purpose RXD is
sampled at a rate of 16 times whatever baud rate has been established. When a transition
is detected, the divide-by-16 counter is immediately reset to align its rollovers with the
boundaries of the incoming bit times.
The 16 states of the counter divide each bit time into 16ths. At the 7th, 8th, and 9th
counter states of each bit time, the bit detector samples the value of RXD. The value
accepted is the value that was seen in at least 2 of the 3 samples. This is done for noise
rejection. If the value accepted during the first bit time is not 0, the receive circuits are
reset and the unit goes back to looking for another 1-to-0 transition. This is to provide
rejection of false start bits. If the start bit proves valid, it is shifted into the input shift
register, and reception of the rest of the frame will proceed.
The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the
following conditions are met at the time the final shift pulse is generated: (a) RI = 0, and
(b) Either SM2 = 0, or the received stop bit = 1.
If either of these two conditions is not met, the received frame is irretrievably lost. If both
conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and RI is
activated.
6.7.7 More about UART modes 2 and 3
Reception is performed in the same manner as in mode 1.
3
TB8
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear
by software as desired.
2
RB8
In Modes 2 and 3, is the 9th data bit that was received. In Mode 1, it
SM2 = 0, RB8 is the stop bit that was received. In Mode 0, RB8 is
undefined.
1
TI
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in
Mode 0, or at the stop bit in the other modes, in any serial
transmission. Must be cleared by software.
0
RI
Receive interrupt flag. Set by hardware at the end of the 8th bit time in
Mode 0, or approximately halfway through the stop bit time in all other
modes. (See SM2 for exceptions). Must be cleared by software.
Table 39.
SCON - Serial port control register (address 98H) SM0/SM1 mode definition
SM0, SM1
UART mode
Baud rate
0 0
0: shift register
CPU clock / 6
0 1
1: 8-bit UART
variable
1 0
2: 9-bit UART
CPU clock / 32 or CPU clock / 16
1 1
3: 9-bit UART
variable
Table 38.
SCON - Serial port control register (address 98H) bit description …continued
Bit
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B3W-CU-B1 | CONVERTER MOD DC/DC 5.5V 200W |
| VJ1825A561KBCAT4X | CAP CER 560PF 200V 10% NP0 1825 |
| P89V664FA,512 | IC 80C51 MCU FLASH 64K 44-PLCC |
| VJ1825A562JBCAT4X | CAP CER 5600PF 200V 5% NP0 1825 |
| VI-B3V-IY-F4 | CONVERTER MOD DC/DC 5.8V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P8-A000001 | 制造商:OTTO Engineering Inc 功能描述:P8-A141313 EXCEPT |
| P8-A000003 | 制造商:OTTO Engineering Inc 功能描述:P8-A121213 WITH |
| P8-A000004 | 制造商:OTTO Engineering Inc 功能描述:P8-A141324 EXCEPT |
| P8-A000005 | 制造商:OTTO Engineering Inc 功能描述:P8-A126323 WITH 24IN |
| P8-A000006 | 制造商:OTTO Engineering Inc 功能描述:P8-A141522 EXCEPT |
發布緊急采購，3分鐘左右您將得到回復。