- 您現在的位置：買賣IC網 > PDF目錄12023 > P89V664FBC,557 (NXP Semiconductors)IC 80C51 MCU FLASH 64K 44-TQFP PDF資料下載
參數資料
| 型號： | P89V664FBC,557 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 11/90頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU FLASH 64K 44-TQFP |
| 產品培訓模塊： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 標準包裝： | 800 |
| 系列： | 89V |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 40MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 36 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-TQFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1001-ND - USB IN-CIRCUIT PROG 80C51ISP |
| 其它名稱： | 568-2437 935280835557 P89V664FBC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
P89V660_662_664
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3.1 — 17 October 2011
19 of 90
NXP Semiconductors
P89V660/662/664
80C51 with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
6.3.3 Boot block
When the microcontroller programs its own flash memory, all of the low level details are
handled by code (bootloader) that is contained in a Boot block. A user program calls the
common entry point in the Boot block with appropriate parameters to accomplish the
desired operation. Boot block operations include erase user code, program user code,
program security bits, chip erase, etc. The Boot block logically overlays the program
memory space from FC00H to FFFFH, when it is enabled. The Boot block may be
disabled on-the-fly so that the upper 1 kB of user code is available to the user’s program.
6.3.4 Power-on reset code execution
The P89V660/662/664 contains two special flash elements: the Boot Vector and the Boot
Status bit. Following reset, the P89V660/662/664 examines the contents of the Boot
Status bit. If the Boot Status bit is set to zero, power-up execution starts at location 0000H,
which is the normal start address of the user’s application code. When the Boot Status bit
is set to a value other than zero, the contents of the Boot Vector are used as the high byte
of the execution address and the low byte is set to 00H
Table 10 shows the factory default Boot Vector setting for this device. A factory-provided
bootloader is pre-programmed into the address space indicated and uses the indicated
boot loader entry point to perform ISP functions.
6.3.5 Hardware activation of the bootloader
The bootloader can also be executed by forcing the device into ISP mode during a
power-on sequence. This has the same effect as having a non-zero status byte. This
allows an application to be built that will normally execute user code but can be manually
forced into ISP operation. If the factory default setting for the boot vector (FCH) is
changed, it will no longer point to the factory pre-programmed ISP bootloader code. After
programming the flash, the status byte should be programmed to zero in order to allow
execution of the user’s application code beginning at address 0000H.
6.3.6 ISP
ISP is performed without removing the microcontroller from the system. The ISP facility
consists of a series of internal hardware resources coupled with internal firmware to
facilitate remote programming of the P89V660/662/664 through the serial port. This
firmware is provided by NXP and embedded within each P89V660/662/664 device. The
NXP ISP facility has made in-circuit programming in an embedded application possible
with a minimum of additional expense in components and circuit board area. The ISP
function uses five pins (VDD, VSS, TXD, RXD, and RST). Only a small connector needs to
be available to interface your application to an external circuit in order to use this feature.
6.3.7 Using ISP
The ISP feature allows for a wide range of baud rates to be used in your application,
independent of the oscillator frequency. It is also adaptable to a wide range of oscillator
frequencies. This is accomplished by measuring the bit-time of a single bit in a received
character. This information is then used to program the baud rate in terms of timer counts
Table 10.
Default boot vector values and ISP entry points
Device
Default boot vector
Default bootloader
entry point
Default bootloader code
range
P89V660/662/664
FCH
FC00H
FC00H to FFFFH
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B3W-CU-B1 | CONVERTER MOD DC/DC 5.5V 200W |
| VJ1825A561KBCAT4X | CAP CER 560PF 200V 10% NP0 1825 |
| P89V664FA,512 | IC 80C51 MCU FLASH 64K 44-PLCC |
| VJ1825A562JBCAT4X | CAP CER 5600PF 200V 5% NP0 1825 |
| VI-B3V-IY-F4 | CONVERTER MOD DC/DC 5.8V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P8-A000001 | 制造商:OTTO Engineering Inc 功能描述:P8-A141313 EXCEPT |
| P8-A000003 | 制造商:OTTO Engineering Inc 功能描述:P8-A121213 WITH |
| P8-A000004 | 制造商:OTTO Engineering Inc 功能描述:P8-A141324 EXCEPT |
| P8-A000005 | 制造商:OTTO Engineering Inc 功能描述:P8-A126323 WITH 24IN |
| P8-A000006 | 制造商:OTTO Engineering Inc 功能描述:P8-A141522 EXCEPT |
發布緊急采購，3分鐘左右您將得到回復。