- 您現在的位置：買賣IC網 > PDF目錄384806 > OXCB950 (Electronic Theatre Controls, Inc.) Integrated High Performance UART Cardbus / PCI interface PDF資料下載
參數資料
| 型號： | OXCB950 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Integrated High Performance UART Cardbus / PCI interface |
| 中文描述： | 綜合高性能的UART Cardbus / PCI接口 |
| 文件頁數： | 33/68頁 |
| 文件大?。?/td> | 409K |
| 代理商： | OXCB950 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Data Sheet Revision 1.1
Page 33
OXCB950
OXFORD SEMICONDUCTOR LTD.
7.3
Reset Configuration
7.3.1
After a hardware reset, all writable registers are reset to
0x00, with the following exceptions:
DLL, which is reset to 0x01.
CPR, which is reset to 0x20.
The state of read-only registers following a hardware reset
is as follows:
RHR[7:0]: Indetermnate
RFL[6:0]: 0000000
2
TFL[6:0]: 0000000
2
LSR[7:0]: 0x60 signifying that both the transmtter and the
transmtter FIFO are empty
MSR[3:0]: 0000
2
MSR[7:4]: Dependent on modeminput lines DCD, RI,
DSR and CTS respectively
ISR[7:0]: 0x01, i.e. no interrupts are pending
ASR[7:0]: 1xx00000
2
RFC[7:0]: 00000000
2
GDS[7:0]: 00000001
2
DMS[7:0]: 00000010
2
CKA[7:0]: 00000000
2
The reset state of output signals are tabulated below:
Signal
Reset state
SOUT
Inactive High
RTS#
Inactive High
DTR#
Inactive High
Hardware Reset
Table 12: Output Signal Reset State
7.3.2
An additional feature available in the OXCB950 UART is
software resetting of the serial channel. This command has
the same effect on a single channel as a hardware reset
except it does not reset the clock source selections (i.e.
CKS register and CKA register). To reset the UART write
0x00 to the Channel Software Reset register ‘CSR’.
Software Reset
相關PDF資料 |
PDF描述 |
|---|---|
| OXFW900 | IEEE1394 to ATA/ATAPI Native Bridge |
| OXFW900-TQ-A | IEEE1394 to ATA/ATAPI Native Bridge |
| OXFW911 | IEEE1394 to ATA/ATAPI Native Bridge |
| OXFW911-TQ-A | IEEE1394 to ATA/ATAPI Native Bridge |
| OZ6812 | ACPI CardBus Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OXCB950-TQAG | 功能描述:外圍驅動器與原件 - PCI 32 bit PC Card bridge to serial prt RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| OXCB950-TQC60-A | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated High Performance UART Cardbus / 3.3v PCI interface |
| OXCF950 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:low cost asynchronous 16-bit PC card or Compact Flash UART device |
| OXCF950_06 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:low cost asynchronous 16-bit PC card or Compact Flash UART device |
| OXCF950B | 制造商:PLX 制造商全稱:PLX 功能描述:16-bit PC card/CF+ bridge to serial port |
發布緊急采購，3分鐘左右您將得到回復。