參數資料
型號： OXFW900-TQ-A
廠商： Electronic Theatre Controls, Inc.
英文描述： IEEE1394 to ATA/ATAPI Native Bridge
中文描述： IEEE1394連接到ATA / ATAPI的母語橋
文件頁數： 1/30頁
文件大?。?/td> 187K
代理商： OXFW900-TQ-A
Oxford Semiconductor Ltd.
69 Mlton Park, Abingdon, Oxon, OX14 4RX, UK
Tel: +44 (0)1235 824900
Fax: +44(0)1235 821141
Oxford Semiconductor 1999
OXFW900 Data Sheet Revision 1.0 – Nov 1999
Part No. OXFW900-TQ-A
F
EATURES
S400 compliant 1394-1995 Link and Transaction
layers
Compatible with 1394-1995 and 1394A Phys.
Buffer Manager with max. RAMbandwidth of
800Mbps
Mcrosoft Win98-Second Edition, Win2000 and Apple
MacOS 8.5 generic driver support
SBP-2 Target Revision 4 compliant interface
Fully ATA-4 compliant (see T13-1153D)
Sustained IDE transfer rate of 25 Mbytes per second,
Peak transfer rate of 50Mbytes per second.
Supports PIO modes 0 to 4, DMA modes 0 to 2 and
Ultra DMA modes 0 to 2
Integrated 32-bit RISC processor (ARM7TDMI) with
on-chip scratch RAM
ORB co-processor to accelerate translation of ORBs
to ATAPI commands
Supports ORB chaining for increased performance
High performance ATA command translation in
firmware using Reduced Block Command (RBC) set
Optional External Serial ROMinterface for
configuration data, user serial number, etc.
Blank Flash memory programmng feature via 1394
bus
3.3 Volts operation
Low Power CMOS
Firmware and Flash Programmng Utilities supplied by
Oxford Semconductor
ultra-thin 128-TQFP package (14mmx 14mmx 1mm)
D
ESCRIPTION
The OXFW900 is a high-performance 1394 to
ATA/ATAPI (IDE) native bridge with an integrated target
Serial Bus Protocol (SBP-2 ) controller.
By supporting
the SBP-2 protocol, the device can use generic SBP-2
drivers available in the Mcrosoft Windows 98SE, Mcrosoft
Windows 2000, Mcrosoft Mllenniumand Apple MacOS
operating systems.
The device is ideally suited for smart-cable or tailgate
interface applications for removable-media drives, compact
flash card readers, CD-ROM CD-R, CD-RW, DVD-ROM
DVD-RAMand hard disk drives, allowing IDE drives to be
connected to a 1394 serial bus in a plug-and-play fashion.
Both ATA and ATAPI devices are supported using the
same firmware.
This highly integrated device offers a three-chip solution to
native bridge applications using an external 1394 PHY and
Flash ROM. A slow 32Kx8 Flash ROM(up to 120ns) is
sufficient for most optical media applications. For
applications that need a sustained data rate in excess of
10Mbytes per second, for example high performance disk
drives, an 8-bit 50ns FLASH or faster is recommended.
The device is compatible with both 1394-1995 and 1394A
PHYs.
The LINK controller complies with S400 1394-1995
specification. The 1394 transaction layer and SBP-2
protocol is implemented using a combination of the
ARM7TDMI (low-power 32-bit RISC processor), an ORB
(Operational Request Block) hardware co-processor and a
high performance buffer manager.
The Buffer Manager has a RAMbandwidth of 800Mbps. It
provides storage for 1394 and ATA/ATAPI packets,
automatically storing themand passing themto the
appropriate destinations, without any intervention fromthe
processor. It also provides storage and manages the
sequencing of ORB fetching to reduce latency and improve
data throughput.
The configuration data including the IEEE OUI
(Organisational Unique Identifier) and device serial number
is stored in the Flash ROMwhich may be uploaded from
the 1394 bus, even when blank. The device also facilitates
firmware uploads fromthe 1394 bus.
The ORB co-processor translates ORBs as defined in the
SBP-2 protocol into ATA/ATAPI commands, and
automatically stores error/status messages at an address
specified by the host.
Concurrent operation of the ATA/ATAPI and 1394
interfaces are facilitated using the high throughput Buffer
Manager where LINK, ATAPI manager and ARM7TDMI
can performinterleaved accesses to the on-chip RAM
buffer. The high performance processor ensures that no
significant latency is incurred. The ATA command
translation is performed in firmware to meet RBC (Reduced
Block Commands) standard, T10-1228D. The ATA/ATAPI
Manager supports PIO modes 0 to 4, DMA modes 0 to 2
and Ultra DMA mode 0 to 2 and provides the interface to
the IDE bus. It is compliant with T13-1153D, ATA-4
specification.
OXFW900
IEEE1394 to ATA/ATAPI Native Bridge
Data Sheet
相關PDF資料
PDF描述
OXFW911 IEEE1394 to ATA/ATAPI Native Bridge
OXFW911-TQ-A IEEE1394 to ATA/ATAPI Native Bridge
OZ6812 ACPI CardBus Controller
OZ6812B ACPI CardBus Controller
OZ6812T ACPI CardBus Controller
相關代理商/技術參數
參數描述
OXFW911 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IEEE1394 to ATA/ATAPI Native Bridge
OXFW911PLUS 制造商:OXFORD 制造商全稱:OXFORD 功能描述:1394A-to-ATA7/ATAPI Bridge
OXFW911-TQ-A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IEEE1394 to ATA/ATAPI Native Bridge
OXFW912 制造商:OXFORD 制造商全稱:OXFORD 功能描述:1394B-to-ATA7/ATAPI Bridge
OXFW970-TQAG 功能描述:USB 接口集成電路 2 in 8 out FireWire audio Cont. RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*