參數資料
型號： OXCB950
廠商： Electronic Theatre Controls, Inc.
英文描述： Integrated High Performance UART Cardbus / PCI interface
中文描述： 綜合高性能的UART Cardbus / PCI接口
文件頁數： 23/68頁
文件大?。?/td> 409K
代理商： OXCB950
6.6.3
For cardbus mode, the cardbus status registers as given by
the tuple CISTPL_CONFIG_CB and located at the memory
base address register BAR4, are disabled (bypassed) by
default. This results in the power management behaviour
for the device in cardbus mode to be identical to the power
management behaviour for the device in the pci mode, with
the exception that the power management event (the
wakeup request) is available on the CSYSCHG pin for
cardbus modes and the PME#pin for pci modes.
The default setting means that all ‘powerdown and
‘wakeup requests, in the cardbus mode, have not been
conditioned by the 4 sets of registers making up the
cardbus status registers. For those applications that require
the cardbus status registers to be enabled, then the power
management logic for cardbus mode incurs the following
controls.
Since all powerdown requests are interrupt requests, then
powerdown requests on the device’s interrupt pin (CINT#)
will be controlled according to the INTR fields of the
cardbus status registers. That is, a powerdown request will
be asserted only if the INTR field in the Function Event
Mask Register has been set and the corresponding field in
the Function Event Register has detected a valid (internal)
power down request. Simlarly, the wakeup (power
management events) are controlled by the GWAKE/WKUP
fields in the cardbus status registers. A ‘wakeup event for
cardbus applications will only be invoked if the
GWAKE/WKUP fields in the Function Event Mask Register
have been enabled and the GWAKE field in the Function
Event Register has detected a ‘wakeup request.
Note that
these controls are on top of the controls for ‘powerdown
and ‘wakeup requests as given in the local configuration
registers
.
These actions are sumarised below (taken fromtable 6-2 of the PC card standard)
Data Sheet Revision 1.1
Page 23
OXCB950
OXFORD SEMICONDUCTOR LTD.
Cardbus Power management
Specifically for the generation of ‘wake-up events, the PC
Card Standard notes that in an ACPI operating system
there is no cardbus device driver and so, in order to
support power management events the PME_EN bit in the
PCI configuration region must support generating a
CSYSCHG signal for a cardbus card. PME_en must make
the cardbus card power management functionality act as if
the cardbus card were a standard PCI device.
To achieve this effect when the cardbus status registers
are enabled, when the operating systemsets the PME_En
bit true (in the PCI power management register block) this
action also sets true the GWAKE bit (bit4) and the WKUP
bit (bit14) fields in the Cardbus Function Event Mask
Register. This ensures that any recognised wakeup events
allow the assertion of the CSYSCHG line. Setting the
PME_En bit false, also clears the GWAKE and WKUP bits
in the Function Event Mask Register to deassert or inhibit
the power management on the CSYSCHG line.
Once the PME_En bit is set, the function targets the
GWAKE bitin the Function Event Register as the functions
general wakeup event. When enabled (PME_En true) any
wakeup events are latched into the PME_status and the
cardbus cards GWAKE bit in the Function Event register.
Clearing the GWAKE/WKUP fields in the Function Event
Mask Register, to disable wakeup events on the CSYCHG
pin, does not clear the PME_En bit in the PCI power
management register block. Writing a ‘1’ to the
PME_status bit of the PCI power management register
block will clear the GWAKE bit in the Function Event
register deasserting the CSYSCHG event. Clearing the
GWAKE bit in the Function Event register, by writing a ‘1’,
clears the PME_status bit in the PMCSR register.
ACPI Operating System
Function Event
Register
GWAKE
Defualt 0
0
0
1(detected wakeup
event)
1
0
Non-ACPI Operating System
Per cardbus electrical sepcification
Cardbus PCI
Configuration Space
PME_En
Default 0
Written 1
1
1
Function Event Mask
Register
GWAKE / WKUP
Default 0 / Default 0
Follows PME_en
1 / 1
1 / 1
Cardbus pin
Cardbus PCI
configuration Space
PME_status
Default 0
0
0
Latches wakeup
(CSYSCHG) event
CSYSCHG
Default0
0
0
1
Written 0
Dont Care
Follows PME_en
Dont care/ Dont care
0
0
No effect
No effect
相關PDF資料
PDF描述
OXFW900 IEEE1394 to ATA/ATAPI Native Bridge
OXFW900-TQ-A IEEE1394 to ATA/ATAPI Native Bridge
OXFW911 IEEE1394 to ATA/ATAPI Native Bridge
OXFW911-TQ-A IEEE1394 to ATA/ATAPI Native Bridge
OZ6812 ACPI CardBus Controller
相關代理商/技術參數
參數描述
OXCB950-TQAG 功能描述:外圍驅動器與原件 - PCI 32 bit PC Card bridge to serial prt RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
OXCB950-TQC60-A 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated High Performance UART Cardbus / 3.3v PCI interface
OXCF950 制造商:OXFORD 制造商全稱:OXFORD 功能描述:low cost asynchronous 16-bit PC card or Compact Flash UART device
OXCF950_06 制造商:OXFORD 制造商全稱:OXFORD 功能描述:low cost asynchronous 16-bit PC card or Compact Flash UART device
OXCF950B 制造商:PLX 制造商全稱:PLX 功能描述:16-bit PC card/CF+ bridge to serial port
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*