- 您現在的位置：買賣IC網 > PDF目錄367625 > MFRC53101T (NXP Semiconductors N.V.) ISO-IEC 14443 reader IC PDF資料下載
參數資料
| 型號： | MFRC53101T |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 通信及網絡 |
| 英文描述： | ISO-IEC 14443 reader IC |
| 封裝： | MFRC53101T/0FE<SOT287-1 (SO32)|<<http://www.nxp.com/packages/SOT287-1.html<1<week 51, 2004,;MFRC53101T/0FE<SOT287-1 (SO32)|<<http://www.nxp.com/packages/SOT287-1.html< |
| 文件頁數： | 84/116頁 |
| 文件大?。?/td> | 862K |
| 代理商： | MFRC53101T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
MFRC531_34
NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.4 — 26 January 2010
056634
84 of 116
NXP Semiconductors
MFRC531
ISO/IEC 14443 reader IC
11.3 EEPROM commands
11.3.1
WriteE2 command 01h
Table 139. WriteE2 command 01h
Command
Value
The WriteE2 command interprets the first two bytes in the FIFO buffer as the EEPROM
start byte address. Any further bytes are interpreted as data bytes and are programmed
into the EEPROM, starting from the given EEPROM start byte address. This command
does not return any data.
The WriteE2 command can only be started by the microprocessor. It will not stop
automatically but has to be stopped explicitly by the microprocessor by issuing the Idle
command.
11.3.1.1
Programming process
Up to 16 bytes can be programmed into the EEPROM during a single programming cycle.
The time needed is approximately 5.8 ms.
The state machine copies all the prepared data bytes to the FIFO buffer and then to the
EEPROM input buffer. The internal EEPROM input buffer is 16 bytes long which is equal
to the block size of the EEPROM. A programming cycle is started if the last position of the
EEPROM input buffer is written or if the last byte of the FIFO buffer has been read.
The E2Ready flag remains logic 0 when there are unprocessed bytes in the FIFO buffer or
the EEPROM programming cycle is still in progress. When all the data from the FIFO
buffer are programmed into the EEPROM, the E2Ready flag is set to logic 1. Together
with the rising edge of E2Ready, the TxIRq interrupt request flag shows logic 1. This can
be used to generate an interrupt when programming of all data is finished.
Remark:
During the E2PROM programming indicated by E2Ready = logic 0, the WriteE2
command cannot be stopped using any other command.
Once E2Ready = logic 1, the WriteE2 command can be stopped by the microprocessor by
sending the Idle command.
Action
FIFO
Arguments and
data
start address LSB
start address MSB
data byte stream
Returned
data
-
-
-
WriteE2
01h
get data from FIFO buffer and write it
to the EEPROM
相關PDF資料 |
PDF描述 |
|---|---|
| MFRX85201HD | Secure contactless reader solution |
| MMBD4148 | High-speed switching diode |
| MMBD6050-V-GS08 | SWITING 70V 0.2A 3PIN SOT-23 - Tape and Reel |
| MMBD6050-V-GS18 | SWITING 70V 0.2A 3PIN SOT-23 - Tape and Reel |
| MMBD7000-V-GS08 | Diode Small Signal Switching 100V 0.2A 3-Pin SOT-23 T/R |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MFRC53101T/0FE,112 | 功能描述:RFID應答器 MIFARE HS READER RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| MFRC53101T/0FE112 | 制造商:NXP Semiconductors 功能描述:CNTCLESS RC 5V ISO14443-A |
| MFRC53101T/0FE112 | 制造商:NXP Semiconductors 功能描述:IC RFID READER 13.56MHZ SOIC-32 |
| MFRC630 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Contactless reader IC |
| MFRC63001HN,518 | 制造商:NXP Semiconductors 功能描述:MFRC63001HN/HVQFN32/REEL13DP// - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。