- 您現在的位置：買賣IC網 > PDF目錄367625 > MFRC53101T (NXP Semiconductors N.V.) ISO-IEC 14443 reader IC PDF資料下載
參數資料
| 型號： | MFRC53101T |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 通信及網絡 |
| 英文描述： | ISO-IEC 14443 reader IC |
| 封裝： | MFRC53101T/0FE<SOT287-1 (SO32)|<<http://www.nxp.com/packages/SOT287-1.html<1<week 51, 2004,;MFRC53101T/0FE<SOT287-1 (SO32)|<<http://www.nxp.com/packages/SOT287-1.html< |
| 文件頁數： | 80/116頁 |
| 文件大?。?/td> | 862K |
| 代理商： | MFRC53101T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
MFRC531_34
NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.4 — 26 January 2010
056634
80 of 116
NXP Semiconductors
MFRC531
ISO/IEC 14443 reader IC
If an EOF pattern is detected or the signal strength falls below the RxThreshold register
MinLevel[3:0] bits setting, both the receiver and the decoder stop. Then the Idle command
is entered and an appropriate response for the microprocessor is generated (interrupt
request activated, status flags set).
When the ChannelRedundancy register bit RxCRCEn is set, a CRC block is expected.
The CRC block can be one byte or two bytes depending on the ChannelRedundancy
register CRC8 bit setting.
Remark:
If the CRC block received is correct, it is not sent to the FIFO buffer. This is
realized by shifting the incoming data bytes through an internal buffer of either one or two
bytes (depending on the defined CRC). The CRC block remains in this internal buffer.
Consequently, all data bytes in the FIFO buffer are delayed by one or two bytes. If the
CRC fails, all received bytes are sent to the FIFO buffer including the faulty CRC.
If ParityEn is set in the ChannelRedundancy register, a parity bit is expected after each
byte. If ParityOdd = logic 1, the expected parity is odd, otherwise even parity is expected.
11.2.2.3
Collision detection
If more than one card is within the RF field during the card selection phase, they both
respond simultaneously. The MFRC531 supports the algorithm defined in
ISO/IEC 14443 A to resolve card serial number data collisions by performing the
anti-collision procedure. The basis for this procedure is the ability to detect bit-collisions.
Bit-collision detection is supported by the Manchester coding bit encoding scheme used in
the MFRC531. If in the first and second half-bit of a subcarrier, modulation is detected,
instead of forwarding a 1-bit or 0-bit, a bit-collision is indicated. The MFRC531 uses the
RxThreshold register CollLevel[3:0] bits setting to distinguish between a 1-bit or 0-bit and
a bit-collision. If the amplitude of the half-bit with smaller amplitude is larger than that
defined by the CollLevel[3:0] bits, the MFRC531 flags a bit-collision using the error flag
CollErr. If a bit-collision is detected in a parity bit, the ParityErr flag is set.
On a detected collision, the receiver continues receiving the incoming data stream. In the
case of a bit-collision, the decoder sends logic 1 at the collision position.
Remark:
As an exception, if bit ZeroAfterColl is set, all bits received after the first
bit-collision are forced to zero, regardless whether a bit-collision or an unequivocal state
has been detected. This feature makes it easier for the control software to perform the
anti-collision procedure as defined in ISO/IEC 14443 A.
When the first bit collision in a frame is detected, the bit-collision position is stored in the
CollPos register.
Table 135
shows the collision positions.
相關PDF資料 |
PDF描述 |
|---|---|
| MFRX85201HD | Secure contactless reader solution |
| MMBD4148 | High-speed switching diode |
| MMBD6050-V-GS08 | SWITING 70V 0.2A 3PIN SOT-23 - Tape and Reel |
| MMBD6050-V-GS18 | SWITING 70V 0.2A 3PIN SOT-23 - Tape and Reel |
| MMBD7000-V-GS08 | Diode Small Signal Switching 100V 0.2A 3-Pin SOT-23 T/R |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MFRC53101T/0FE,112 | 功能描述:RFID應答器 MIFARE HS READER RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| MFRC53101T/0FE112 | 制造商:NXP Semiconductors 功能描述:CNTCLESS RC 5V ISO14443-A |
| MFRC53101T/0FE112 | 制造商:NXP Semiconductors 功能描述:IC RFID READER 13.56MHZ SOIC-32 |
| MFRC630 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Contactless reader IC |
| MFRC63001HN,518 | 制造商:NXP Semiconductors 功能描述:MFRC63001HN/HVQFN32/REEL13DP// - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。