- 您現在的位置：買賣IC網 > PDF目錄45022 > M306H3FCFP 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP116 PDF資料下載
參數資料
| 型號： | M306H3FCFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP116 |
| 封裝： | 20 X 20 MM, 0.65 MM PITCH, PLASTIC, LQFP-116 |
| 文件頁數： | 83/135頁 |
| 文件大?。?/td> | 2583K |
| 代理商： | M306H3FCFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
Rev.1.00
2004.03.23
page 51 of 320
M306H3MC-XXXFP/FCFP
(3) Stop Mode
In stop mode, all oscillator circuits are turned off, so are the CPU clock and the peripheral function clocks.
Therefore, the CPU and the peripheral functions clocked by these clocks stop operating. The least
amount of power is consumed in this mode. If the voltage applied to Vcc pins is VRAM or more, the internal
RAM is retained.
However, the peripheral functions clocked by external signals keep operating. The following interrupts
can be used to exit stop mode.
______
NMI interrupt
Key interrupt
______
INT interrupt
Timer A, Timer B interrupt (when counting external pulses in event counter mode)
Serial I/O interrupt (when external clock is seleted)
The internal oscillator circuit of expansion function (Data acquisition / humming function) stops oscillation
when expansion register XTAL_VCO, PDC_VCO_ON, VPS_VCO_ON = "L".
Entering Stop Mode
The microcomputer is placed into stop mode by setting the CM10 bit of CM1 register to “1” (all clocks
turned off). At the same time, the CM06 bit of CM0 register is set to “1” (divide-by-8 mode) and the
CM15 bit of CM10 register is set to “1” (main clock oscillator circuit drive capability high).
Pin Status in Stop Mode
Table 2.5.4 lists pin status during stop mode
Exiting Stop Mode
______
The microcomputer is moved out of stop mode by a hardware reset, NMI interrupt or peripheral func-
tion interrupt.
______
If the microcomputer is to be moved out of stop mode by a hardware reset or NMI interrupt, set the
peripheral function interrupt priority ILVL2 to ILVL0 bits to “0002” (interrupts disable) before setting the
CM10 bit to “1”.
If the microcomputer is to be moved out of stop mode by a peripheral function interrupt, set up the
following before setting the CM10 bit to “1”.
1. In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the periph-
eral function interrupt to be used to exit stop mode.
Also, for all of the peripheral function interrupts not used to exit stop mode, set the ILVL2 to ILVL0
bits to “0002”.
2. Set the I flag to “1”.
3. Enable the peripheral function whose interrupt is to be used to exit stop mode.
In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an
interrupt service routine is executed.
______
Which CPU clock will be used after exiting stop mode by a peripheral function or NMI interrupt is
determined by the CPU clock that was on when the microcomputer was placed into stop mode as
follows:
If the CPU clock before entering stop mode was derived from the sub clock: sub clock
If the CPU clock before entering stop mode was derived from the main clock: main clock divide-by-8
相關PDF資料 |
PDF描述 |
|---|---|
| M306H5MG-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP116 |
| M306H5MG-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP116 |
| M306H5FGFP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP116 |
| M306N4FGVFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M306N4MGT-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M306H3FCFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 128KB FLASH 5V 116LQFP - Trays |
| M306H3MC-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
| M306H5FGFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
| M306H5FGFP#U0 | 功能描述:IC M16C/6H MCU FLASH 116LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60 標準包裝:160 系列:S08 核心處理器:S08 芯體尺寸:8-位 速度:40MHz 連通性:I²C，LIN，SCI，SPI 外圍設備:LCD，LVD，POR，PWM，WDT 輸入/輸出數:53 程序存儲器容量:32KB（32K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1.9K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 12x12b 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:64-LQFP 包裝:托盤 |
| M306H5MC-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。