參數資料
型號: M306H3FCFP
元件分類: 微控制器/微處理器
英文描述: 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP116
封裝: 20 X 20 MM, 0.65 MM PITCH, PLASTIC, LQFP-116
文件頁數: 76/135頁
文件大?。?/td> 2583K
代理商: M306H3FCFP
Rev.1.00
2004.03.23
page 45 of 320
M306H3MC-XXXFP/FCFP
Microcomputer
(Built-in feedback resistor)
XCIN
XCOUT
Externally derived clock
Open
Vcc
Vss
Note: Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive
capacity setting. Use the value recommended by the maker of the oscillator.
When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's
data sheet specifies that a feedback resistor be added external to the chip, insert a feedback resistor between XCIN
and XCOUT following the instruction.
Microcomputer
(Built-in feedback resistor)
XCIN
XCOUT
(Note)
CCIN
CCOUT
RCd
Figure 2.5.6. Examples of Sub Clock Connection Circuit
(2) Sub Clock
The sub clock is generated by the sub clock oscillation circuit. This clock is used as the clock source for
the CPU clock, as well as the timer A and timer B count sources. In addition, an fc clock with the same
frequency as that of the sub clock can be output from the CLKOUT pin.
The sub clock oscillator circuit is configured by connecting a crystal resonator between the XCIN and
XCOUT pins. The sub clock oscillator circuit contains a feedback resistor, which is disconnected from the
oscillator circuit during stop mode in order to reduce the amount of power consumed in the chip. The sub
clock oscillator circuit may also be configured by feeding an externally generated clock to the XCIN pin.
Figure 2.5.6 shows the examples of sub clock connection circuit.
When the level on the START pin is “H ”, the sub clock is turned off after reset. At this time, the feedback
resistor is disconnected from the oscillator circuit.
To use the sub clock for the CPU clock, set the CM07 bit of CM0 register to “1 ” (sub clock) after the sub
clock becomes oscillating stably.
When a START pin is “L ”, the sub clock (XCIN) divided by 8 becomes the CPU clock after reset (the main
clock stops). When you use a main clock after this, please shift according to the procedure shown in Fig.
2.5.7.
During stop mode, all clocks including the sub clock are turned off. Refer to “power control”.
相關PDF資料
PDF描述
M306H5MG-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP116
M306H5MG-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP116
M306H5FGFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP116
M306N4FGVFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M306N4MGT-XXXFP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M306H3FCFP#U0 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 128KB FLASH 5V 116LQFP - Trays
M306H3MC-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER
M306H5FGFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER
M306H5FGFP#U0 功能描述:IC M16C/6H MCU FLASH 116LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:M16C™ M16C/60 標準包裝:160 系列:S08 核心處理器:S08 芯體尺寸:8-位 速度:40MHz 連通性:I²C,LIN,SCI,SPI 外圍設備:LCD,LVD,POR,PWM,WDT 輸入/輸出數:53 程序存儲器容量:32KB(32K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1.9K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 12x12b 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:64-LQFP 包裝:托盤
M306H5MC-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER