參數資料
型號: XE8000EV108
廠商: Semtech
文件頁數: 31/143頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XE8806/XE8807
標準包裝: 1
類型: MCU
適用于相關產品: XE88LC06AMI026
所含物品: 完全組裝的評估板
產品目錄頁面: 585 (CN2011-ZH PDF)
Semtech 2006
www.semtech.com
17-5
XE8806A/XE8807A
17.6
General counter registers operation
Counters are enabled by CntAEnable, CntBEnable, CntCEnable, and CntDEnable in RegCntOn.
To stop the counter X, CntXEnable must be reset. To start the counter X, CntXEnable must be set. When
counters are cascaded, CntAEnable and CntCEnable also control respectively the counters B and D.
All counters have a corresponding 8-bit read/write register: RegCntA, RegCntB, RegCntC, and RegCntD. When
read, these registers contain the counter value (or the captured counter value). When written, they modify the
counter comparison values.
It is possible to read any counter at any time, even when the counter is running. The value is guaranteed to be
correct when the counter is running on an internal clock source. For a correct acquisition of the counter value when
running on an external clock source, use one of the three following methods:
1) For slow operating counters (typically at least 8 times slower than the CPU clock), oversample the counter
content and perform a majority operation on the consecutive read results to select the correct actual
content of the counter.
2) Stop the concerned counter, perform the read operation and restart the counter. While stopped, the
counter content is frozen and the counter does not take into account the clock edges delivered on the
external pin.
3) Use the capture mechanism.
When a value is written into the counter register while the counter is in counter mode, both the comparison value is
updated and the counter value is modified. In upcount mode, the register value is reset to zero. In downcount
mode, the comparison value is loaded into the counter. Due to the synchronization mechanism between the
processor clock domain and the external clock source domain, this modification of the counter value can be
postponed until the counter is enabled and that it receives it’s first valid clock edge.
In the PWM mode or in the capture mode, the counter value is not modified by the write operation in the counter
register. Changing to the counter mode, does not update the counter value (no reset in upcount, no load in
downcount mode).
17.7
Clock selection
The clock source for each counter can be individually selected by writing the appropriate value in the register
RegCntCtrlCk.
Table 17-11 gives the correspondence between the binary codes used for the configuration bits CntACkSel(1:0),
CntBCkSel(1:0), CntCCkSel(1:0) or CntDCkSel(1:0) and the clock source selected respectively for the counters
A, B, C or D.
Clock source for
CntXCkSel(1:0)
CounterA
CounterB
CounterC
CounterD
11
Ck128
10
CkRcExt/4
Ck1k
01
CkRcExt
Ck32k
00
PA(0)
PA(1)
PA(2)
PA(3)
Table 17-11: Clock sources for counters A, B, C and D
The CkRcExt clock is the RC oscillator or external clock. The clocks below 32kHz can be derived from the RC
oscillator, the external clock source or the crystal oscillator (see the documentation of the clock block). A separate
external clock source can be delivered on PortA for each individula counter.
相關PDF資料
PDF描述
94SVP476X0020E7 CAP ALUM 47UF 20V 20% SMD
EBC22DRTI-S13 CONN EDGECARD 44POS .100 EXTEND
AT-S-26-8/8/B-14-R MOD CORD STANDARD 8-8 BLACK 14'
LGU2E221MELZ CAP ALUM 220UF 250V 20% SNAP
VE-BT1-EY CONVERTER MOD DC/DC 12V 50W
相關代理商/技術參數
參數描述
XE8000EV110 功能描述:EVAL BOARD FOR XE8802AMI035LF RoHS:否 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:- 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板,軟件,4x4 鍵盤,光學撥輪,QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
XE8000EV120 功能描述:BOARD EVAL FOR SX8722I070TRLF RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:ZoomingADC™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
XE8000EV121 功能描述:BOARD EVAL FOR SX8723/24 RoHS:是 類別:編程器,開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理,電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
XE8000MP 功能描述:PROG BOARD AND PROSTART2 CARD RoHS:否 類別:編程器,開發系統 >> 獨立編程器 系列:- 產品目錄繪圖:CHIPPROG-G4 標準包裝:1 系列:- 類型:成組編程器 適用于相關產品:EEPROM,EPROM,F(xiàn)LASH,MCU,NVRAM,PLD 所含物品:編程器,線纜,CD 產品目錄頁面:598 (CN2011-ZH PDF) 相關產品:AE-TS56-16I-3-ND - ISP CABLEADAPTER 14-PIN HEADERAE-TS40N-ND - ADAPTER SOCKET 40-TSOP TO 40-DIPAE-TS32N-ND - ADAPTER SOCKET 32-TSOP TO 32-DIPAE-TS28-ND - ADAPTER SOCKET 28-TSOP TO 28-DIPAE-T44-P16-ND - ADAPTER SOCKET 44-QFP TO 40-DIPAE-T44-I51/505-ND - ADAPTER SOCKET 44-QFP TO 40-DIPAE-SS56-16I-ND - ADAPTER SOCKET 56-SSOP TO 40-DIPAE-SP8U-ND - ADAPTER SOCKET 8-SSOP TO 8-DIPAE-SP28U2-ND - ADAPTER SOCKET 28-SSOP TO 28-DIPAE-SP28U1-ND - ADAPTER SOCKET 28-SSOP TO 28-DIP更多...
XE8801A 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Data Acquisition with ZoomingADC?