- 您現在的位置：買賣IC網 > PDF目錄203625 > W25Q16VSFIG (WINBOND ELECTRONICS CORP) 2M X 8 SPI BUS SERIAL EEPROM, PDSO16 PDF資料下載
參數資料
| 型號： | W25Q16VSFIG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 2M X 8 SPI BUS SERIAL EEPROM, PDSO16 |
| 封裝： | 0.300 INCH, GREEN, PLASTIC, SOIC-16 |
| 文件頁數： | 29/60頁 |
| 文件大?。?/td> | 1438K |
| 代理商： | W25Q16VSFIG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
W25Q16V
Publication Release Date: October 7, 2009
- 35 -
Revision E
10.2.18 32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24-bit block address (A23-A0) (see Figure 2). The
Block Erase instruction sequence is shown in figure 18.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (SEC, TB, BP2,
BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 18. 32KB Block Erase Instruction Sequence Diagram
Note:
For W25Q16, user should not issue 32KB Block Erase (52h) instruction to the top or bottom 32KB block
when SEC bit in Status Register is set to “1”.
相關PDF資料 |
PDF描述 |
|---|---|
| W25Q32DWZPIP | 256K X 16 SPI BUS SERIAL EEPROM, 7.5 ns, PDSO8 |
| W25Q80VZPIG | 1M X 8 SPI BUS SERIAL EEPROM, DSO8 |
| W25X16AVDAIZ | 2M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X40AVSSIG | 512K X 8 FLASH 2.7V PROM, PDSO8 |
| W25X80AVDAIZ | 1M X 8 FLASH 2.7V PROM, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q16VSSIG | 功能描述:IC FLASH 16MBIT 80MHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 產品變化通告:Product Discontinuation 26/Apr/2010 標準包裝:136 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步，DDR II 存儲容量:18M（1M x 18） 速度:200MHz 接口:并聯 電源電壓:1.7 V ~ 1.9 V 工作溫度:0°C ~ 70°C 封裝/外殼:165-TBGA 供應商設備封裝:165-CABGA（13x15） 包裝:托盤 其它名稱:71P71804S200BQ |
| W25Q16VZPIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BWSNIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BWSNIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
發布緊急采購，3分鐘左右您將得到回復。