- 您現在的位置：買賣IC網 > PDF目錄203625 > W25Q16VSFIG (WINBOND ELECTRONICS CORP) 2M X 8 SPI BUS SERIAL EEPROM, PDSO16 PDF資料下載
參數資料
| 型號： | W25Q16VSFIG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 2M X 8 SPI BUS SERIAL EEPROM, PDSO16 |
| 封裝： | 0.300 INCH, GREEN, PLASTIC, SOIC-16 |
| 文件頁數： | 2/60頁 |
| 文件大?。?/td> | 1438K |
| 代理商： | W25Q16VSFIG |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
W25Q16V
- 10 -
9. FUNCTIONAL DESCRIPTION
9.1 SPI OPERATIONS
9.1.1
Standard SPI Instructions
The W25Q16 is accessed through an SPI compatible bus consisting of four signals: Serial Clock (CLK),
Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions use the
DI input pin to serially write instructions, addresses or data to the device on the rising edge of CLK. The
DO output pin is used to read data or status from the device on the falling edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0
and Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and
data is not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the
falling and rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising
edges of /CS.
9.1.2
Dual SPI Instructions
The W25Q16 supports Dual SPI operation when using the "Fast Read Dual Output and Dual I/O" (3B
and BB hex) instructions. These instructions allow data to be transferred to or from the device at two to
three times the rate of ordinary Serial Flash devices. The Dual Read instructions are ideal for quickly
downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical code
directly from the SPI bus (XIP). When using Dual SPI instructions the DI and DO pins become
bidirectional I/O pins: IO0 and IO1.
9.1.3
Quad SPI Instructions
The W25Q16 supports Quad SPI operation when using the "Fast Read Quad Output and Fast Read
Quad I/O" (6B and EB hex respectively). These instructions allow data to be transferred to or from the
device four to six times the rate of ordinary Serial Flash. The Quad Read instructions offer a significant
improvement in continuous and random access transfer rates allowing fast code-shadowing to RAM or
execution directly from the SPI bus (XIP). When using Quad SPI instructions the DI and DO pins
become bidirectional IO0 and IO1, and the /WP and /HOLD pins become IO2 and IO3 respectively.
Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set.
9.1.4
Hold Function
The /HOLD signal allows the W25Q16 operation to be paused while it is actively selected (when /CS is
low). The /HOLD function may be useful in cases where the SPI data and clock signals are shared with
other devices. For example, consider if the page buffer was only partially written when a priority
interrupt requires use of the SPI bus. In this case the /HOLD function can save the state of the
instruction and the data in the buffer so programming can resume where it left off once the bus is
available again. The /HOLD function is only available for standard SPI and Dual SPI operation, not
during Quad SPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on
the rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial
Data Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored.
The Chip Select (/CS) signal should be kept active (low) for the full duration of the /HOLD operation to
avoid resetting the internal logic state of the device.
相關PDF資料 |
PDF描述 |
|---|---|
| W25Q32DWZPIP | 256K X 16 SPI BUS SERIAL EEPROM, 7.5 ns, PDSO8 |
| W25Q80VZPIG | 1M X 8 SPI BUS SERIAL EEPROM, DSO8 |
| W25X16AVDAIZ | 2M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X40AVSSIG | 512K X 8 FLASH 2.7V PROM, PDSO8 |
| W25X80AVDAIZ | 1M X 8 FLASH 2.7V PROM, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q16VSSIG | 功能描述:IC FLASH 16MBIT 80MHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 產品變化通告:Product Discontinuation 26/Apr/2010 標準包裝:136 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步，DDR II 存儲容量:18M（1M x 18） 速度:200MHz 接口:并聯 電源電壓:1.7 V ~ 1.9 V 工作溫度:0°C ~ 70°C 封裝/外殼:165-TBGA 供應商設備封裝:165-CABGA（13x15） 包裝:托盤 其它名稱:71P71804S200BQ |
| W25Q16VZPIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BWSNIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BWSNIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
發布緊急采購，3分鐘左右您將得到回復。