參數資料
型號： TSB82AA2I
廠商： Texas Instruments, Inc.
英文描述： 1394b OHCI-LYNX CONTROLLER
中文描述： 的1394b OHCI的山貓控制器
文件頁數： 62/104頁
文件大?。?/td> 461K
代理商： TSB82AA2I
420
Table 416. Interrupt Event Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
22
cycleLost
RSCU
A lost cycle is indicated when no cycle_start packet is sent or received between two successive
cycleSynch events. A lost cycle can be predicted when a cycle_start packet does not immediately
follow the first subaction gap after the cycleSynch event or if an arbitration reset gap is detected after
a cycleSynch event without an intervening cycle start. Bit 22 may be set either when a lost cycle
occurs or when logic predicts that one will occur.
Indicates that the 7th bit of the cycle second counter has changed.
21
cycle64Seconds
RSCU
20
cycleSynch
RSCU
Indicates that a new isochronous cycle has started. Bit 20 is set to 1 when the low order bit of the
cycle count toggles.
19
phy
RSCU
Indicates that the PHY device requests an interrupt through a status transfer.
18
regAccessFail
RSCU
Indicates that a TSB82AA2 register access has failed due to a missing SCLK clock signal from the
PHY device. When a register access fails, bit 18 is set to 1 before the next register access.
17
busReset
RSCU
Indicates that the PHY device has entered bus reset mode.
16
selfIDcomplete
RSCU
A self-ID packet stream has been received. It is generated at the end of the bus initialization process.
Bit 16 is turned off simultaneously when bit 17 (busReset) is turned on.
15
selfIDcomplete2
RSCU
Secondary indication of the end of a self-ID packet stream. Bit 15 is set to 1 by the TSB82AA2 device
when it sets bit 16 (selfIDcomplete), and retains its state, independent of bit 17 (busReset).
1410
RSVD
R
Reserved. Bits 1410 return 0s when read.
9
lockRespErr
RSCU
Indicates that the TSB82AA2 device sent a lock response for a lock request to a serial bus register,
but did not receive an ack_complete.
8
postedWriteErr
RSCU
Indicates that a host bus error occurred while the TSB82AA2 device was trying to write a 1394 write
request, which had already been given an ack_complete, into system memory.
7
isochRx
RU
Isochronous receive DMA interrupt. Indicates that one or more isochronous receive contexts have
generated an interrupt. This is not a latched event; it is the logical OR of all bits in the isochronous
receive interrupt event register at OHCI offset A0h/A4h (see Section 4.25,
Isochronous Receive
Interrupt Event Register
) and isochronous receive interrupt mask register at OHCI offset A8h/ACh
(see Section 4.26,
Isochronous Receive Interrupt Mask Register
). The isochronous receive interrupt
event register indicates which contexts have been interrupted.
6
isochTx
RU
Isochronous transmit DMA interrupt. Indicates that one or more isochronous transmit contexts have
generated an interrupt. This is not a latched event, it is the logical OR of all bits in the isochronous
transmit interrupt event register at OHCI offset 90h/94h (see Section 4.23,
Isochronous Transmit
Interrupt Event Register
) and isochronous transmit interrupt mask register at OHCI offset 98h/9Ch
(see Section 4.24,
Isochronous Transmit Interrupt Mask Register
). The isochronous transmit
interrupt event register indicates which contexts have been interrupted.
5
RSPkt
RSCU
Indicates that a packet was sent to an asynchronous receive response context buffer and the
descriptor’s xferStatus and resCount fields have been updated.
4
RQPkt
RSCU
Indicates that a packet was sent to an asynchronous receive request context buffer and the
descriptor’s xferStatus and resCount fields have been updated.
3
ARRS
RSCU
Asynchronous receive response DMA interrupt. Bit 3 is conditionally set to 1 upon completion of an
ARRS DMA context command descriptor.
2
ARRQ
RSCU
Asynchronous receive request DMA interrupt. Bit 2 is conditionally set to 1 upon completion of an
ARRQ DMA context command descriptor.
1
respTxComplete
RSCU
Asynchronous response transmit DMA interrupt. Bit 1 is conditionally set to upon completion of an
ATRS DMA command.
0
reqTxComplete
RSCU
Asynchronous request transmit DMA interrupt. Bit 0 is conditionally set to 1 upon completion of an
ATRQ DMA command.
相關PDF資料
PDF描述
TSC2200EVM TSC2200 Touch Screen Controller Evaluation Module(TSC2200觸摸屏控制器評估模塊)
TSC427CBA Dual Power MOSFET Drivers
TSC427CPA Dual Power MOSFET Drivers
TSC428CBA Dual Power MOSFET Drivers
TSC426CBA Dual Power MOSFET Drivers
相關代理商/技術參數
參數描述
TSB82AA2IPGE 功能描述:接口 - 專用 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
TSB82AA2IPGEEP 功能描述:1394 接口集成電路 Mil Enh 1394b OHCI- Lynx Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB82AA2PGE 功能描述:1394 接口集成電路 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB82AA2PGEG4 功能描述:1394 接口集成電路 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB82AA2ZGW 功能描述:1394 接口集成電路 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*