- 您現在的位置：買賣IC網 > PDF目錄383967 > TSB82AA2I (Texas Instruments, Inc.) 1394b OHCI-LYNX CONTROLLER PDF資料下載
參數資料
| 型號： | TSB82AA2I |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 1394b OHCI-LYNX CONTROLLER |
| 中文描述： | 的1394b OHCI的山貓控制器 |
| 文件頁數： | 57/104頁 |
| 文件大?。?/td> | 461K |
| 代理商： | TSB82AA2I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
415
Table 412. Host Controller Control Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
22
aPhyEnhanceEnable
RSC
When bits 23 (programPhyEnable) and 17 (linkEnable) are 1, the OHCI driver can set bit 22 to
1 to use all IEEE 1394a-2000 enhancements. When bit 23 (programPhyEnable) is cleared to 0,
the software does not change PHY enhancements or this bit.
2120
RSVD
R
Reserved. Bits 2120 return 0s when read.
19
LPS
RSC
Bit 19 controls the link power status. Software must set this bit to 1 to permit link-PHY
communication. A 0 prevents link-PHY communication.
The OHCI-link is divided into two clock domains (PCI_CLK and PHY_SCLK). If software tries to
access any register in the PHY_SCLK domain while the PHY_SCLK is disabled, then a target
abort is issued by the link. This problem can be avoided by setting bit 4 (DIS_TGT_ABT) in the
miscellaneous configuration register at offset F0h in the PCI configuration space (see
Section 3.23,
Miscellaneous Configuration Register
). This allows the link to respond to these
types of request by returning all Fs (hex).
OHCI registers at offsets DChF0h and 100h11Ch are in the PHY_SCLK domain.
After setting LPS, software must wait approximately 10 ms before attempting to access any of
the OHCI registers. This gives the PHY_SCLK time to stabilize.
18
postedWriteEnable
RSC
Bit 18 enables (1) or disables (0) posted writes. Software changes this bit only when bit 17
(linkEnable) is 0.
17
linkEnable
RSC
Bit 17 is cleared to 0 by either a system (hardware) or software reset. Software must set this bit
to 1 when the system is ready to begin operation and then force a bus reset. This bit is necessary
to keep other nodes from sending transactions before the local system is ready. When this bit is
cleared, the TSB82AA2 device is logically and immediately disconnected from the 1394 bus, no
packets are received or processed, nor are packets transmitted.
16
SoftReset
RSCU
When bit 16 is set to 1, all TSB82AA2 states are reset, all FIFOs are flushed, and all OHCI
registers are set to their system (hardware) reset values, unless otherwise specified. PCI
registers are not affected by this bit. This bit remains set to 1 while the software reset is in progress
and reverts back to 0 when the reset has completed.
150
RSVD
R
Reserved. Bits 150 return 0s when read.
4.17 Self-ID Buffer Pointer Register
The self-ID buffer pointer register points to the 2K-byte aligned base address of the buffer in host memory where the
self-ID packets are stored during bus initialization. Bits 3111 are read/write accessible. Bits 100 are reserved, and
return 0s when read.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Self-ID buffer pointer
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Self-ID buffer pointer
Type
R/W
R/W
R/W
R/W
R/W
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
Register:
Type:
Offset:
Default:
Self-ID buffer pointer
Read/Write, Read-only
64h
XXXX XX00h
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2200EVM | TSC2200 Touch Screen Controller Evaluation Module(TSC2200觸摸屏控制器評估模塊) |
| TSC427CBA | Dual Power MOSFET Drivers |
| TSC427CPA | Dual Power MOSFET Drivers |
| TSC428CBA | Dual Power MOSFET Drivers |
| TSC426CBA | Dual Power MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB82AA2IPGE | 功能描述:接口 - 專用 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TSB82AA2IPGEEP | 功能描述:1394 接口集成電路 Mil Enh 1394b OHCI- Lynx Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB82AA2PGE | 功能描述:1394 接口集成電路 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB82AA2PGEG4 | 功能描述:1394 接口集成電路 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB82AA2ZGW | 功能描述:1394 接口集成電路 OHCI-Lynx Controller RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。